Simplify SUBGHZSPI configuration.

This commit is contained in:
ceekdee 2023-05-04 09:45:18 -05:00
parent b1ef856242
commit 91612b7446
4 changed files with 5 additions and 14 deletions

View File

@ -194,17 +194,17 @@ impl<'d, T: Instance, Tx, Rx> Spi<'d, T, Tx, Rx> {
Self::new_inner(peri, None, Some(mosi.map_into()), None, txdma, rxdma, freq, config)
}
#[cfg(stm32wl)]
/// Useful for on chip peripherals like SUBGHZ which are hardwired.
#[allow(dead_code)]
pub fn new_subghz(
peri: impl Peripheral<P = T> + 'd,
txdma: impl Peripheral<P = Tx> + 'd,
rxdma: impl Peripheral<P = Rx> + 'd,
pclk3_freq: u32,
) -> Self {
// see RM0453 rev 1 section 7.2.13 page 291
// The SUBGHZSPI_SCK frequency is obtained by PCLK3 divided by two.
// The SUBGHZSPI_SCK clock maximum speed must not exceed 16 MHz.
let pclk3_freq = <peripherals::SUBGHZSPI as crate::rcc::sealed::RccPeripheral>::frequency().0;
let freq = Hertz(core::cmp::min(pclk3_freq / 2, 16_000_000));
let mut config = Config::default();
config.mode = MODE_0;

View File

@ -11,8 +11,6 @@ use embassy_executor::Spawner;
use embassy_lora::iv::Stm32wlInterfaceVariant;
use embassy_lora::LoraTimer;
use embassy_stm32::gpio::{Level, Output, Pin, Speed};
use embassy_stm32::peripherals::SUBGHZSPI;
use embassy_stm32::rcc::low_level::RccPeripheral;
use embassy_stm32::rng::Rng;
use embassy_stm32::spi::Spi;
use embassy_stm32::{interrupt, into_ref, pac, Peripheral};
@ -36,8 +34,7 @@ async fn main(_spawner: Spawner) {
unsafe { pac::RCC.ccipr().modify(|w| w.set_rngsel(0b01)) }
let pclk3_freq = SUBGHZSPI::frequency().0;
let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2, pclk3_freq);
let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2);
let irq = interrupt::take!(SUBGHZ_RADIO);
into_ref!(irq);

View File

@ -10,8 +10,6 @@ use defmt::info;
use embassy_executor::Spawner;
use embassy_lora::iv::Stm32wlInterfaceVariant;
use embassy_stm32::gpio::{Level, Output, Pin, Speed};
use embassy_stm32::peripherals::SUBGHZSPI;
use embassy_stm32::rcc::low_level::RccPeripheral;
use embassy_stm32::spi::Spi;
use embassy_stm32::{interrupt, into_ref, Peripheral};
use embassy_time::{Delay, Duration, Timer};
@ -28,8 +26,7 @@ async fn main(_spawner: Spawner) {
config.rcc.mux = embassy_stm32::rcc::ClockSrc::HSE32;
let p = embassy_stm32::init(config);
let pclk3_freq = SUBGHZSPI::frequency().0;
let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2, pclk3_freq);
let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2);
let irq = interrupt::take!(SUBGHZ_RADIO);
into_ref!(irq);

View File

@ -10,8 +10,6 @@ use defmt::info;
use embassy_executor::Spawner;
use embassy_lora::iv::Stm32wlInterfaceVariant;
use embassy_stm32::gpio::{Level, Output, Pin, Speed};
use embassy_stm32::peripherals::SUBGHZSPI;
use embassy_stm32::rcc::low_level::RccPeripheral;
use embassy_stm32::spi::Spi;
use embassy_stm32::{interrupt, into_ref, Peripheral};
use embassy_time::Delay;
@ -28,8 +26,7 @@ async fn main(_spawner: Spawner) {
config.rcc.mux = embassy_stm32::rcc::ClockSrc::HSE32;
let p = embassy_stm32::init(config);
let pclk3_freq = SUBGHZSPI::frequency().0;
let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2, pclk3_freq);
let spi = Spi::new_subghz(p.SUBGHZSPI, p.DMA1_CH1, p.DMA1_CH2);
let irq = interrupt::take!(SUBGHZ_RADIO);
into_ref!(irq);