776: Automatically set ADC clock prescaler on v2 ADC to respect max frequency r=Dirbaio a=matoushybl
Co-authored-by: Matous Hybl <hyblmatous@gmail.com>
763: Misc USB improvements r=Dirbaio a=Dirbaio
The "simplify control in/out handlng" commit gives a -2kb code size improvement.
766: Make usb_serial examples work on windows r=Dirbaio a=timokroeger
Windows shows `error 10` when using CDC ACM on non composite devices.
Workaround is to use IADS:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/kconfig/CONFIG_CDC_ACM_IAD.html#help
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
Co-authored-by: Timo Kröger <timo.kroeger@hitachienergy.com>
The replacement is `embassy-usb`. There's a WIP driver for stm32 USBD in #709,
there's no WIP driver for stm32 USB_OTG. This means we're left without
USB_OTG support for now.
Reason for removing is I'm going to soon remove `embassy::io`, and
USB uses it. I don't want to spend time maintaining "dead" code
that is going to be removed. Volunteers welcome, either to update
old USB to the new IO, or write a USB_OTG driver fo the new USB.
743: Add PLL config support for F2 r=Dirbaio a=Gekkio
- minor changes to make the F2 RCC API a bit more flexible
- low-level PLL config with assertions based on datasheet specs. It shouldn't be very difficult to later add a "reverse API" where you pass the clocks you want to a function and it generates a `PLLConfig` struct for you
- PLL API tested on my custom board with 12 MHz HSE as source for PLL to generate max clocks for SYSCLK/AHB/APB/APB1/PLL48
- the example *should* work but is untested since I don't have the Nucleo board 😞
Co-authored-by: Joonas Javanainen <joonas.javanainen@gmail.com>
SMI Ethernet PHYs all share a common base set of registers that can do
90% of all tasks. The LAN8742 driver used some vendor-specific
registers to check link negotiation status, but the need for that was
debatable, so I migrated it to a generic driver instead, anybody who
wants extra functionality can copy it and impl their own on top of it.
* Less generics on bootloader. Keep PAGE_SIZE as a common multiple of
DFU and ACTIVE page sizes.
* Document restriction
* Add unit tests for different page sizes
* Add flash drivers for L0, L1, L4, WB and WL. Not tested for WB, but
should be similar to WL.
* Add embassy-boot-stm32 for bootloading on STM32.
* Add flash examples and bootloader examples
* Update stm32-data
734: executor: Add `Spawner::for_current_executor`. r=Dirbaio a=Dirbaio
This is needed to spawn non-Send tasks in an InterruptExecutor, after the fixes in #730 .
`@matoushybl` could you check if this works for your use case?
735: stm32: add stm32u5 GPDMA, SPIv4 support, add HIL tests. r=Dirbaio a=Dirbaio
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
The initial closure is not actually called in the interrupt, so this is
illegally sending non-Send futures to the interrupt.
Remove the closure, and return a SendSpawner instead.
* Add FlashProvider and FlashConfig traits to define flash
characteristics
* Use traits in bootloader to retrieve flash handles and for
copying data between flash instances
* Add convenience implementations for using a single flash instance.
* Adds implementations of embedded-storage and embedded-storage-async
for QSPI
* Add blocking implementations of QSPI
* Use blocking implementation in new() and embedded-storage impls
* Use async implementation in embedded-storage-async impls
* Add FLASH_SIZE const generic parameter
* Own IRQ in Qspi to disable it on drop
- Renamed structs to HidReaderWriter, HidReader, HidWriter.
- Removed unused const generics on `State`.
- Simplified generics on `HidReaderWriter`.
The class type previously was `HidClass<D, Driver<'d, USBD>, ReportReader<'d, Driver<'d, USBD>, OUT_N>, IN_N>`
It's now `HidClass<D, Driver<'d, USBD>, IN_N, OUT_N>`. Note that the driver type `Driver<'d, USBD>` is no longer repeated.
- Constructors are now: `HidWriter::new()` for IN-only, `HidReaderWriter::new()` for IN+OUT. No complicated bounds.
- HidReaderWriter has all the methods from HidReader, HidWriter.
711: Add DeviceStateHandler, DeviceCommand channel, and remote wakeup support r=Dirbaio a=alexmoon
Apologies for the size of this PR. Once I started getting into the Vbus power management side of my device I found a couple of areas of functionality missing from embassy-usb. Specifically, I need the application to be able to respond to changes in the USB device state in order to properly control the amount of power I'm drawing from Vbus. I also wanted to enable remote wakeup support for my device.
In order to enable device state monitoring, I've created a `DeviceStateHandler` trait and made it possible to pass in an optional reference a handler implementing that trait when creating the `UsbDeviceBuilder`.
Remote wakeup required a way to send commands to the bus which is exclusively owned by the `UsbDevice::run` method. This is the same problem we were discussing for enabling/disabling the device on Vbus power events. My solution is to allow an optional `Channel` to be provided to the `UsbDeviceBuilder` (via `UsbDeviceBuilder::new_with_channel`), allowing the application to send commands into the `run` method. Right now it supports enable, disable and remote wakeup commands.
Since there's now a way to dynamically enable and disable the device, I also added `Config::start_enabled` to control whether or not the `UsbDevice` should start in the enabled state. That also allowed me to make `UsbDeviceBuilder::build` sync again and move enabling the bus into `UsbDevice::run`.
This led to a few driver changes:
1. `Driver::enable` became `Driver::into_bus`
2. `Bus::enable`, `Bus::disable`, and `Bus::remote_wakeup` were added
3. I removed `Bus::reset`, `Bus::suspend`, and `Bus::resume` because they were only ever called based on the result of `Bus::poll`. It made more sense to me to have `Bus::poll` handle the driver-specific state management itself.
I've updated the `usb_hid_keyboard` example to take advantage of all these additional features.
Let me know what you think.
Thanks!
Co-authored-by: alexmoon <alex.r.moon@gmail.com>
714: add more clock options for l4 and l5 r=Dirbaio a=ant32
- added an assert so it panics if pll48div is not 48Mhz
- added MSI as a clock source for PLL
- removed hsi48 option for MCUs mentioned in l4 rcc presentation
- copied some code from l4 to l5, but don't have a way of testing it.
Co-authored-by: Philip A Reimer <antreimer@gmail.com>
657: Async usb stack r=Dirbaio a=Dirbaio
TODO
- [x] Make it work on nRF
- [x] Add a way for classes to handle their own EP0 control requests - thanks `@alexmoon!`
- [x] Handle CONTROL OUT requests with data.
- [ ] Impl AsyncRead/AsyncWrite for CDC ACM -- will do later, it's not trivial
- [x] Cleanup unwraps/asserts/panics
- [x] Cleanup logs (make everything trace/debug, not info)
- [ ] Port synopsys-usb-otg
- [ ] Port stm32-usbd
- [ ] Add more classes? HID, MSD?
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
Co-authored-by: alexmoon <alex.r.moon@gmail.com>
696: Add async Mutex. r=Dirbaio a=Dirbaio
What it says on the tin :)
It allows sharing data between tasks when you want to `.await` stuff while holding it locked.
Co-authored-by: Dario Nieuwenhuis <dirbaio@dirbaio.net>
- Allow initializing in a static, without Forever.
- Remove ability to close, since in embedded enviromnents channels usually live forever and don't get closed.
- Remove MPSC restriction, it's MPMC now. Rename "mpsc" to "channel".
- `Sender` and `Receiver` are still available if you want to enforce a piece of code only has send/receive access, but are optional: you can send/receive directly into the Channel if you want.
