docs/modules/ROOT/pages/faq.adoc

@@ -35,7 +35,7 @@ For Cortex-M targets, consider making sure that ALL of the following features ar
 * `executor-thread`
 * `nightly`
 
-For ESP32, consider using the executors and `#[main]` macro provided by your appropriate link:https://crates.io/crates/esp-hal-common[HAL crate].
+For Xtensa ESP32, consider using the executors and `#[main]` macro provided by your appropriate link:https://crates.io/crates/esp-hal-common[HAL crate].
 
 == Why is my binary so big?
 

embassy-boot/boot/src/firmware_updater/blocking.rs

@@ -184,12 +184,10 @@ impl<'d, DFU: NorFlash, STATE: NorFlash> BlockingFirmwareUpdater<'d, DFU, STATE>
     ///
     /// Failing to meet alignment and size requirements may result in a panic.
     pub fn write_firmware(&mut self, offset: usize, data: &[u8]) -> Result<(), FirmwareUpdaterError> {
-        //assert!(data.len() >= DFU::ERASE_SIZE);
+        assert!(data.len() >= DFU::ERASE_SIZE);
         self.state.verify_booted()?;
 
-        if offset == 0 {
-            self.dfu.erase(0, self.dfu.capacity() as u32)?;
-        }
+        self.dfu.erase(offset as u32, (offset + data.len()) as u32)?;
 
         self.dfu.write(offset as u32, data)?;
 

embassy-stm32/src/usart/mod.rs

@@ -161,10 +161,6 @@ pub struct Config {
     /// Set this to true to invert RX pin signal values (V<sub>DD</sub> =0/mark, Gnd = 1/idle).
     #[cfg(any(usart_v3, usart_v4))]
     pub invert_rx: bool,
-
-    /// enable single wire half duplex communication. Only the tx pin is used. Needs an external
-    /// pull up
-    pub half_duplex: bool,
 }
 
 impl Default for Config {
@@ -184,7 +180,6 @@ impl Default for Config {
             invert_tx: false,
             #[cfg(any(usart_v3, usart_v4))]
             invert_rx: false,
-            half_duplex: false,
         }
     }
 }
@@ -816,13 +811,6 @@ impl<'d, T: BasicInstance, TxDma, RxDma> Uart<'d, T, TxDma, RxDma> {
         let r = T::regs();
 
         // Some chips do not have swap_rx_tx bit
-        if config.half_duplex {
-            if config.swap_rx_tx {
-                rx.set_as_af(rx.af_num(), AFType::OutputOpenDrain);
-            } else {
-                tx.set_as_af(tx.af_num(), AFType::OutputOpenDrain);
-            }
-        } else {
         cfg_if::cfg_if! {
             if #[cfg(any(usart_v3, usart_v4))] {
                 if config.swap_rx_tx {
@@ -838,7 +826,6 @@ impl<'d, T: BasicInstance, TxDma, RxDma> Uart<'d, T, TxDma, RxDma> {
                 tx.set_as_af(tx.af_num(), AFType::OutputPushPull);
             }
         }
-        }
 
         configure(r, &config, T::frequency(), T::KIND, true, true)?;
 
@@ -1052,7 +1039,6 @@ fn configure(
     #[cfg(not(usart_v1))]
     r.cr3().modify(|w| {
         w.set_onebit(config.assume_noise_free);
-        w.set_hdsel(config.half_duplex);
     });
 
     r.cr1().write(|w| {

embassy-usb-dfu/src/application.rs

@@ -73,8 +73,6 @@ impl<'d, STATE: NorFlash, RST: Reset> Handler for Control<'d, STATE, RST> {
                 self.detach_start = Some(Instant::now());
                 self.timeout = Some(Duration::from_millis(req.value as u64));
                 self.state = State::AppDetach;
-                // hack to make it work together with usb serial logging
-                self.reset();
                 Some(OutResponse::Accepted)
             }
             _ => None,