use stm32_metapac::flash::vals::Latency;
use stm32_metapac::rcc::vals::{Hpre, Pllsrc, Ppre, Sw};
use stm32_metapac::FLASH;

pub use super::common::{AHBPrescaler, APBPrescaler};
use crate::pac::{PWR, RCC};
use crate::rcc::sealed::RccPeripheral;
use crate::rcc::{set_freqs, Clocks};
use crate::time::Hertz;

/// HSI speed
pub const HSI_FREQ: Hertz = Hertz(16_000_000);

/// LSI speed
pub const LSI_FREQ: Hertz = Hertz(32_000);

/// System clock mux source
#[derive(Clone, Copy)]
pub enum ClockSrc {
    HSE(Hertz),
    HSI16,
    PLL,
}

impl Into<u8> for APBPrescaler {
    fn into(self) -> u8 {
        match self {
            PllSrc::HSE(..) => Pllsrc::HSE,
            PllSrc::HSI16 => Pllsrc::HSI16,
        }
    }
}

seq_macro::seq!(P in 2..=31 {
    /// Output divider for the PLL P output.
    #[derive(Clone, Copy)]
    pub enum PllP {
        // Note: If PLL P is set to 0 the PLLP bit controls the output division. There does not seem to
        // a good reason to do this so the API does not support it.
        // Div1 is invalid
        #(
            Div~P,
        )*
    }

    impl From<PllP> for u8 {
        /// Returns the register value for the P output divider.
        fn from(val: PllP) -> u8 {
            match val {
                #(
                    PllP::Div~P => P,
                )*
            }
        }
    }
});

impl PllP {
    /// Returns the numeric value of the P output divider.
    pub fn to_div(self) -> u32 {
        let val: u8 = self.into();
        val as u32
    }
}

/// Output divider for the PLL Q output.
#[derive(Clone, Copy)]
pub enum PllQ {
    Div2,
    Div4,
    Div6,
    Div8,
}

impl PllQ {
    /// Returns the numeric value of the Q output divider.
    pub fn to_div(self) -> u32 {
        let val: u8 = self.into();
        (val as u32 + 1) * 2
    }
}

impl From<PllQ> for u8 {
    /// Returns the register value for the Q output divider.
    fn from(val: PllQ) -> u8 {
        match val {
            PllQ::Div2 => 0b00,
            PllQ::Div4 => 0b01,
            PllQ::Div6 => 0b10,
            PllQ::Div8 => 0b11,
        }
    }
}

/// Output divider for the PLL R output.
#[derive(Clone, Copy)]
pub enum PllR {
    Div2,
    Div4,
    Div6,
    Div8,
}

impl PllR {
    /// Returns the numeric value of the R output divider.
    pub fn to_div(self) -> u32 {
        let val: u8 = self.into();
        (val as u32 + 1) * 2
    }
}

impl From<PllR> for u8 {
    /// Returns the register value for the R output divider.
    fn from(val: PllR) -> u8 {
        match val {
            PllR::Div2 => 0b00,
            PllR::Div4 => 0b01,
            PllR::Div6 => 0b10,
            PllR::Div8 => 0b11,
        }
    }
}

seq_macro::seq!(N in 8..=127 {
    /// Multiplication factor for the PLL VCO input clock.
    #[derive(Clone, Copy)]
    pub enum PllN {
        #(
            Mul~N,
        )*
    }

    impl From<PllN> for u8 {
        /// Returns the register value for the N multiplication factor.
        fn from(val: PllN) -> u8 {
            match val {
                #(
                    PllN::Mul~N => N,
                )*
            }
        }
    }

    impl PllN {
        /// Returns the numeric value of the N multiplication factor.
        pub fn to_mul(self) -> u32 {
            match self {
                #(
                    PllN::Mul~N => N,
                )*
            }
        }
    }
});

/// PLL Pre-division. This must be set such that the PLL input is between 2.66 MHz and 16 MHz.
#[derive(Copy, Clone)]
pub enum PllM {
    Div1,
    Div2,
    Div3,
    Div4,
    Div5,
    Div6,
    Div7,
    Div8,
    Div9,
    Div10,
    Div11,
    Div12,
    Div13,
    Div14,
    Div15,
    Div16,
}

impl PllM {
    /// Returns the numeric value of the M pre-division.
    pub fn to_div(self) -> u32 {
        let val: u8 = self.into();
        val as u32 + 1
    }
}

impl From<PllM> for u8 {
    /// Returns the register value for the M pre-division.
    fn from(val: PllM) -> u8 {
        match val {
            PllM::Div1 => 0b0000,
            PllM::Div2 => 0b0001,
            PllM::Div3 => 0b0010,
            PllM::Div4 => 0b0011,
            PllM::Div5 => 0b0100,
            PllM::Div6 => 0b0101,
            PllM::Div7 => 0b0110,
            PllM::Div8 => 0b0111,
            PllM::Div9 => 0b1000,
            PllM::Div10 => 0b1001,
            PllM::Div11 => 0b1010,
            PllM::Div12 => 0b1011,
            PllM::Div13 => 0b1100,
            PllM::Div14 => 0b1101,
            PllM::Div15 => 0b1110,
            PllM::Div16 => 0b1111,
        }
    }
}

/// PLL Configuration
///
/// Use this struct to configure the PLL source, input frequency, multiplication factor, and output
/// dividers. Be sure to keep check the datasheet for your specific part for the appropriate
/// frequency ranges for each of these settings.
pub struct Pll {
    /// PLL Source clock selection.
    pub source: PllSrc,

    /// PLL pre-divider
    pub prediv_m: PllM,

    /// PLL multiplication factor for VCO
    pub mul_n: PllN,

    /// PLL division factor for P clock (ADC Clock)
    pub div_p: Option<PllP>,

    /// PLL division factor for Q clock (USB, I2S23, SAI1, FDCAN, QSPI)
    pub div_q: Option<PllQ>,

    /// PLL division factor for R clock (SYSCLK)
    pub div_r: Option<PllR>,
}

impl AHBPrescaler {
    const fn div(self) -> u32 {
        match self {
            AHBPrescaler::NotDivided => 1,
            AHBPrescaler::Div2 => 2,
            AHBPrescaler::Div4 => 4,
            AHBPrescaler::Div8 => 8,
            AHBPrescaler::Div16 => 16,
            AHBPrescaler::Div64 => 64,
            AHBPrescaler::Div128 => 128,
            AHBPrescaler::Div256 => 256,
            AHBPrescaler::Div512 => 512,
        }
    }
}

impl APBPrescaler {
    const fn div(self) -> u32 {
        match self {
            APBPrescaler::NotDivided => 1,
            APBPrescaler::Div2 => 2,
            APBPrescaler::Div4 => 4,
            APBPrescaler::Div8 => 8,
            APBPrescaler::Div16 => 16,
        }
    }
}

impl Into<Ppre> for APBPrescaler {
    fn into(self) -> Ppre {
        match self {
            APBPrescaler::NotDivided => Ppre::DIV1,
            APBPrescaler::Div2 => Ppre::DIV2,
            APBPrescaler::Div4 => Ppre::DIV4,
            APBPrescaler::Div8 => Ppre::DIV8,
            APBPrescaler::Div16 => Ppre::DIV16,
        }
    }
}

impl Into<Hpre> for AHBPrescaler {
    fn into(self) -> Hpre {
        match self {
            AHBPrescaler::NotDivided => Hpre::DIV1,
            AHBPrescaler::Div2 => Hpre::DIV2,
            AHBPrescaler::Div4 => Hpre::DIV4,
            AHBPrescaler::Div8 => Hpre::DIV8,
            AHBPrescaler::Div16 => Hpre::DIV16,
            AHBPrescaler::Div64 => Hpre::DIV64,
            AHBPrescaler::Div128 => Hpre::DIV128,
            AHBPrescaler::Div256 => Hpre::DIV256,
            AHBPrescaler::Div512 => Hpre::DIV512,
        }
    }
}

/// Sets the source for the 48MHz clock to the USB and RNG peripherals.
pub enum Clock48MhzSrc {
    /// Use the High Speed Internal Oscillator. For USB usage, the CRS must be used to calibrate the
    /// oscillator to comply with the USB specification for oscillator tolerance.
    Hsi48(Option<CrsConfig>),
    /// Use the PLLQ output. The PLL must be configured to output a 48MHz clock. For USB usage the
    /// PLL needs to be using the HSE source to comply with the USB specification for oscillator
    /// tolerance.
    PllQ,
}

/// Sets the sync source for the Clock Recovery System (CRS).
pub enum CrsSyncSource {
    /// Use an external GPIO to sync the CRS.
    Gpio,
    /// Use the Low Speed External oscillator to sync the CRS.
    Lse,
    /// Use the USB SOF to sync the CRS.
    Usb,
}

/// Clocks configutation
pub struct Config {
    pub mux: ClockSrc,
    pub ahb_pre: AHBPrescaler,
    pub apb1_pre: APBPrescaler,
    pub apb2_pre: APBPrescaler,
    pub low_power_run: bool,
    /// Iff PLL is requested as the main clock source in the `mux` field then the PLL configuration
    /// MUST turn on the PLLR output.
    pub pll: Option<Pll>,
    /// Sets the clock source for the 48MHz clock used by the USB and RNG peripherals.
    pub clock_48mhz_src: Option<Clock48MhzSrc>,
}

/// Configuration for the Clock Recovery System (CRS) used to trim the HSI48 oscillator.
pub struct CrsConfig {
    /// Sync source for the CRS.
    pub sync_src: CrsSyncSource,
}

impl Default for Config {
    #[inline]
    fn default() -> Config {
        Config {
            mux: ClockSrc::HSI16,
            ahb_pre: AHBPrescaler::NotDivided,
            apb1_pre: APBPrescaler::NotDivided,
            apb2_pre: APBPrescaler::NotDivided,
            low_power_run: false,
            pll: None,
            clock_48mhz_src: None,
        }
    }
}

pub struct PllFreq {
    pub pll_p: Option<Hertz>,
    pub pll_q: Option<Hertz>,
    pub pll_r: Option<Hertz>,
}

pub(crate) unsafe fn init(config: Config) {
    let pll_freq = config.pll.map(|pll_config| {
        let src_freq = match pll_config.source {
            PllSrc::HSI16 => {
                RCC.cr().write(|w| w.set_hsion(true));
                while !RCC.cr().read().hsirdy() {}

                HSI_FREQ.0
            }
            PllSrc::HSE(freq) => {
                RCC.cr().write(|w| w.set_hseon(true));
                while !RCC.cr().read().hserdy() {}
                freq.0
            }
        };

        // Disable PLL before configuration
        RCC.cr().modify(|w| w.set_pllon(false));
        while RCC.cr().read().pllrdy() {}

        let internal_freq = src_freq / pll_config.prediv_m.to_div() * pll_config.mul_n.to_mul();

        RCC.pllcfgr().write(|w| {
            w.set_plln(pll_config.mul_n.into());
            w.set_pllm(pll_config.prediv_m.into());
            w.set_pllsrc(pll_config.source.into());
        });

        let pll_p_freq = pll_config.div_p.map(|div_p| {
            RCC.pllcfgr().modify(|w| {
                w.set_pllpdiv(div_p.into());
                w.set_pllpen(true);
            });
            Hertz(internal_freq / div_p.to_div())
        });

        let pll_q_freq = pll_config.div_q.map(|div_q| {
            RCC.pllcfgr().modify(|w| {
                w.set_pllq(div_q.into());
                w.set_pllqen(true);
            });
            Hertz(internal_freq / div_q.to_div())
        });

        let pll_r_freq = pll_config.div_r.map(|div_r| {
            RCC.pllcfgr().modify(|w| {
                w.set_pllr(div_r.into());
                w.set_pllren(true);
            });
            Hertz(internal_freq / div_r.to_div())
        });

        // Enable the PLL
        RCC.cr().modify(|w| w.set_pllon(true));
        while !RCC.cr().read().pllrdy() {}

        PllFreq {
            pll_p: pll_p_freq,
            pll_q: pll_q_freq,
            pll_r: pll_r_freq,
        }
    });

    let (sys_clk, sw) = match config.mux {
        ClockSrc::HSI16 => {
            // Enable HSI16
            RCC.cr().write(|w| w.set_hsion(true));
            while !RCC.cr().read().hsirdy() {}

            (HSI_FREQ.0, Sw::HSI16)
        }
        ClockSrc::HSE(freq) => {
            // Enable HSE
            RCC.cr().write(|w| w.set_hseon(true));
            while !RCC.cr().read().hserdy() {}

            (freq.0, Sw::HSE)
        }
        ClockSrc::PLL => {
            assert!(pll_freq.is_some());
            assert!(pll_freq.as_ref().unwrap().pll_r.is_some());

            let freq = pll_freq.as_ref().unwrap().pll_r.unwrap().0;

            assert!(freq <= 170_000_000);

            if freq >= 150_000_000 {
                // Enable Core Boost mode on freq >= 150Mhz ([RM0440] p234)
                PWR.cr5().modify(|w| w.set_r1mode(false));
                // Set flash wait state in boost mode based on frequency ([RM0440] p191)
                if freq <= 36_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS0));
                } else if freq <= 68_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS1));
                } else if freq <= 102_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS2));
                } else if freq <= 136_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS3));
                } else {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS4));
                }
            } else {
                PWR.cr5().modify(|w| w.set_r1mode(true));
                // Set flash wait state in normal mode based on frequency ([RM0440] p191)
                if freq <= 30_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS0));
                } else if freq <= 60_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS1));
                } else if freq <= 80_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS2));
                } else if freq <= 120_000_000 {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS3));
                } else {
                    FLASH.acr().modify(|w| w.set_latency(Latency::WS4));
                }
            }

            (freq, Sw::PLLRCLK)
        }
    };

    RCC.cfgr().modify(|w| {
        w.set_sw(sw);
        w.set_hpre(config.ahb_pre.into());
        w.set_ppre1(config.apb1_pre.into());
        w.set_ppre2(config.apb2_pre.into());
    });

    let ahb_freq: u32 = match config.ahb_pre {
        AHBPrescaler::NotDivided => sys_clk,
        pre => sys_clk / pre.div(),
    };

    let (apb1_freq, apb1_tim_freq) = match config.apb1_pre {
        APBPrescaler::NotDivided => (ahb_freq, ahb_freq),
        pre => {
            let freq = ahb_freq / pre.div();
            (freq, freq * 2)
        }
    };

    let (apb2_freq, apb2_tim_freq) = match config.apb2_pre {
        APBPrescaler::NotDivided => (ahb_freq, ahb_freq),
        pre => {
            let freq = ahb_freq / pre.div();
            (freq, freq * 2)
        }
    };

    // Setup the 48 MHz clock if needed
    if let Some(clock_48mhz_src) = config.clock_48mhz_src {
        let source = match clock_48mhz_src {
            Clock48MhzSrc::PllQ => {
                // Make sure the PLLQ is enabled and running at 48Mhz
                let pllq_freq = pll_freq.as_ref().and_then(|f| f.pll_q);
                assert!(pllq_freq.is_some() && pllq_freq.unwrap().0 == 48_000_000);

                crate::pac::rcc::vals::Clk48sel::PLLQCLK
            }
            Clock48MhzSrc::Hsi48(crs_config) => {
                // Enable HSI48
                RCC.crrcr().modify(|w| w.set_hsi48on(true));
                // Wait for HSI48 to turn on
                while RCC.crrcr().read().hsi48rdy() == false {}

                // Enable and setup CRS if needed
                if let Some(crs_config) = crs_config {
                    crate::peripherals::CRS::enable();

                    let sync_src = match crs_config.sync_src {
                        CrsSyncSource::Gpio => crate::pac::crs::vals::Syncsrc::GPIO,
                        CrsSyncSource::Lse => crate::pac::crs::vals::Syncsrc::LSE,
                        CrsSyncSource::Usb => crate::pac::crs::vals::Syncsrc::USB,
                    };

                    crate::pac::CRS.cfgr().modify(|w| {
                        w.set_syncsrc(sync_src);
                    });

                    // These are the correct settings for standard USB operation. If other settings
                    // are needed there will need to be additional config options for the CRS.
                    crate::pac::CRS.cr().modify(|w| {
                        w.set_autotrimen(true);
                        w.set_cen(true);
                    });
                }
                crate::pac::rcc::vals::Clk48sel::HSI48
            }
        };

        RCC.ccipr().modify(|w| w.set_clk48sel(source));
    }

    if config.low_power_run {
        assert!(sys_clk <= 2_000_000);
        PWR.cr1().modify(|w| w.set_lpr(true));
    }

    set_freqs(Clocks {
        sys: Hertz(sys_clk),
        ahb1: Hertz(ahb_freq),
        ahb2: Hertz(ahb_freq),
        apb1: Hertz(apb1_freq),
        apb1_tim: Hertz(apb1_tim_freq),
        apb2: Hertz(apb2_freq),
        apb2_tim: Hertz(apb2_tim_freq),
    });
}