62 lines
2.3 KiB
Plaintext
62 lines
2.3 KiB
Plaintext
= Getting started
|
|
|
|
So you want to try Embassy, great! To get started, there are a few tools you need to install:
|
|
|
|
* link:https://rustup.rs/[rustup] - the Rust toolchain is needed to compile Rust code.
|
|
* link:https://crates.io/crates/probe-rs[probe-rs] - to flash the firmware on your device. If you already have other tools like `OpenOCD` setup, you can use that as well.
|
|
|
|
If you don't have any supported board, don't worry: you can also run embassy on your PC using the `std` examples.
|
|
|
|
== Getting a board with examples
|
|
|
|
Embassy supports many microcontroller families, but the easiest ways to get started is if you have one of the more common development kits.
|
|
|
|
=== nRF kits
|
|
|
|
* link:https://www.nordicsemi.com/Products/Development-hardware/nrf52-dk[nRF52 DK]
|
|
* link:https://www.nordicsemi.com/Products/Development-hardware/nRF9160-DK[nRF9160 DK]
|
|
|
|
=== STM32 kits
|
|
|
|
* link:https://www.st.com/en/evaluation-tools/nucleo-h743zi.html[STM32 Nucleo-144 development board with STM32H743ZI MCU]
|
|
* link:https://www.st.com/en/evaluation-tools/nucleo-f429zi.html[STM32 Nucleo-144 development board with STM32F429ZI MCU]
|
|
* link:https://www.st.com/en/evaluation-tools/b-l4s5i-iot01a.html[STM32L4+ Discovery kit IoT node, low-power wireless, BLE, NFC, WiFi]
|
|
* link:https://www.st.com/en/evaluation-tools/b-l072z-lrwan1.html[STM32L0 Discovery kit LoRa, Sigfox, low-power wireless]
|
|
* link:https://www.st.com/en/evaluation-tools/nucleo-wl55jc.html[STM32 Nucleo-64 development board with STM32WL55JCI MCU]
|
|
* link:https://www.st.com/en/evaluation-tools/b-u585i-iot02a.html[Discovery kit for IoT node with STM32U5 series]
|
|
|
|
|
|
=== RP2040 kits
|
|
|
|
* link:https://www.raspberrypi.com/products/raspberry-pi-pico/[Raspberry Pi Pico]
|
|
|
|
=== ESP32
|
|
|
|
* link:https://github.com/esp-rs/esp-rust-board[ESP32C3]
|
|
|
|
== Running an example
|
|
|
|
First you need to clone the [github repository];
|
|
|
|
[source, bash]
|
|
----
|
|
git clone https://github.com/embassy-rs/embassy.git
|
|
cd embassy
|
|
----
|
|
|
|
You can run an example by opening a terminal and entering the following commands:
|
|
|
|
[source, bash]
|
|
----
|
|
cd examples/nrf52840
|
|
cargo run --bin blinky --release
|
|
----
|
|
|
|
== What's next?
|
|
|
|
Congratulations, you have your first Embassy application running! Here are some alternatives on where to go from here:
|
|
|
|
* Read more about the xref:runtime.adoc[executor].
|
|
* Read more about the xref:hal.adoc[HAL].
|
|
* Start xref:basic_application.adoc[writing your application].
|