457 lines
14 KiB
Rust
457 lines
14 KiB
Rust
#![deny(clippy::pedantic)]
|
||
#![allow(clippy::doc_markdown)]
|
||
#![no_main]
|
||
#![no_std]
|
||
// Needed unitl https://github.com/rust-lang/rust/issues/63063 is stablised.
|
||
#![feature(type_alias_impl_trait)]
|
||
#![feature(associated_type_bounds)]
|
||
#![allow(clippy::missing_errors_doc)]
|
||
|
||
// This example works on a ANALOG DEVICE EVAL-ADIN110EBZ board.
|
||
// Settings switch S201 "HW CFG":
|
||
// - Without SPI CRC: OFF-ON-OFF-OFF-OFF
|
||
// - With SPI CRC: ON -ON-OFF-OFF-OFF
|
||
// Settings switch S303 "uC CFG":
|
||
// - CFG0: On = static ip, Off = Dhcp
|
||
// - CFG1: Ethernet `FCS` on TX path: On, Off
|
||
// The webserver shows the actual temperature of the onboard i2c temp sensor.
|
||
|
||
use core::marker::PhantomData;
|
||
use core::sync::atomic::{AtomicI32, Ordering};
|
||
|
||
use defmt::{error, info, println, unwrap, Format};
|
||
use defmt_rtt as _; // global logger
|
||
use embassy_executor::Spawner;
|
||
use embassy_futures::select::{select, Either};
|
||
use embassy_futures::yield_now;
|
||
use embassy_net::tcp::TcpSocket;
|
||
use embassy_net::{Ipv4Address, Ipv4Cidr, Stack, StackResources, StaticConfigV4};
|
||
use embassy_time::{Delay, Duration, Ticker, Timer};
|
||
use embedded_hal_async::i2c::I2c as I2cBus;
|
||
use embedded_io::Write as bWrite;
|
||
use embedded_io_async::Write;
|
||
use hal::gpio::{Input, Level, Output, Speed};
|
||
use hal::i2c::{self, I2c};
|
||
use hal::rng::{self, Rng};
|
||
use hal::{bind_interrupts, exti, pac, peripherals};
|
||
use heapless::Vec;
|
||
use rand::RngCore;
|
||
use static_cell::make_static;
|
||
use {embassy_stm32 as hal, panic_probe as _};
|
||
|
||
bind_interrupts!(struct Irqs {
|
||
I2C3_EV => i2c::EventInterruptHandler<peripherals::I2C3>;
|
||
I2C3_ER => i2c::ErrorInterruptHandler<peripherals::I2C3>;
|
||
RNG => rng::InterruptHandler<peripherals::RNG>;
|
||
});
|
||
|
||
use embassy_net_adin1110::{self, Device, Runner, ADIN1110};
|
||
use embedded_hal_bus::spi::ExclusiveDevice;
|
||
use hal::gpio::Pull;
|
||
use hal::i2c::Config as I2C_Config;
|
||
use hal::spi::{Config as SPI_Config, Spi};
|
||
use hal::time::Hertz;
|
||
|
||
// Basic settings
|
||
// MAC-address used by the adin1110
|
||
const MAC: [u8; 6] = [0xaa, 0xbb, 0xcc, 0xdd, 0xee, 0xff];
|
||
// Static IP settings
|
||
const IP_ADDRESS: Ipv4Cidr = Ipv4Cidr::new(Ipv4Address([192, 168, 1, 5]), 24);
|
||
// Listen port for the webserver
|
||
const HTTP_LISTEN_PORT: u16 = 80;
|
||
|
||
pub type SpeSpi = Spi<'static, peripherals::SPI2, peripherals::DMA1_CH1, peripherals::DMA1_CH2>;
|
||
pub type SpeSpiCs = ExclusiveDevice<SpeSpi, Output<'static, peripherals::PB12>, Delay>;
|
||
pub type SpeInt = exti::ExtiInput<'static, peripherals::PB11>;
|
||
pub type SpeRst = Output<'static, peripherals::PC7>;
|
||
pub type Adin1110T = ADIN1110<SpeSpiCs>;
|
||
pub type TempSensI2c = I2c<'static, peripherals::I2C3, peripherals::DMA1_CH6, peripherals::DMA1_CH7>;
|
||
|
||
static TEMP: AtomicI32 = AtomicI32::new(0);
|
||
|
||
#[embassy_executor::main]
|
||
async fn main(spawner: Spawner) {
|
||
defmt::println!("Start main()");
|
||
|
||
let mut config = embassy_stm32::Config::default();
|
||
{
|
||
use embassy_stm32::rcc::*;
|
||
// 80Mhz clock (Source: 8 / SrcDiv: 1 * PllMul 20 / ClkDiv 2)
|
||
// 80MHz highest frequency for flash 0 wait.
|
||
config.rcc.mux = ClockSrc::PLL1_R;
|
||
config.rcc.hse = Some(Hse {
|
||
freq: Hertz::mhz(8),
|
||
mode: HseMode::Oscillator,
|
||
});
|
||
config.rcc.pll = Some(Pll {
|
||
source: PllSource::HSE,
|
||
prediv: PllPreDiv::DIV1,
|
||
mul: PllMul::MUL20,
|
||
divp: None,
|
||
divq: None,
|
||
divr: Some(PllRDiv::DIV2), // sysclk 80Mhz clock (8 / 1 * 20 / 2)
|
||
});
|
||
config.rcc.hsi48 = Some(Default::default()); // needed for RNG
|
||
}
|
||
|
||
let dp = embassy_stm32::init(config);
|
||
|
||
// RM0432rev9, 5.1.2: Independent I/O supply rail
|
||
// After reset, the I/Os supplied by VDDIO2 are logically and electrically isolated and
|
||
// therefore are not available. The isolation must be removed before using any I/O from
|
||
// PG[15:2], by setting the IOSV bit in the PWR_CR2 register, once the VDDIO2 supply is present
|
||
pac::PWR.cr2().modify(|w| w.set_iosv(true));
|
||
|
||
let reset_status = pac::RCC.bdcr().read().0;
|
||
defmt::println!("bdcr before: 0x{:X}", reset_status);
|
||
|
||
defmt::println!("Setup IO pins");
|
||
|
||
// Setup LEDs
|
||
let _led_uc1_green = Output::new(dp.PC13, Level::Low, Speed::Low);
|
||
let mut led_uc2_red = Output::new(dp.PE2, Level::High, Speed::Low);
|
||
let led_uc3_yellow = Output::new(dp.PE6, Level::High, Speed::Low);
|
||
let led_uc4_blue = Output::new(dp.PG15, Level::High, Speed::Low);
|
||
|
||
// Read the uc_cfg switches
|
||
let uc_cfg0 = Input::new(dp.PB2, Pull::None);
|
||
let uc_cfg1 = Input::new(dp.PF11, Pull::None);
|
||
let _uc_cfg2 = Input::new(dp.PG6, Pull::None);
|
||
let _uc_cfg3 = Input::new(dp.PG11, Pull::None);
|
||
|
||
// Setup I2C pins
|
||
let temp_sens_i2c = I2c::new(
|
||
dp.I2C3,
|
||
dp.PG7,
|
||
dp.PG8,
|
||
Irqs,
|
||
dp.DMA1_CH6,
|
||
dp.DMA1_CH7,
|
||
Hertz(100_000),
|
||
I2C_Config::default(),
|
||
);
|
||
|
||
// Setup IO and SPI for the SPE chip
|
||
let spe_reset_n = Output::new(dp.PC7, Level::Low, Speed::Low);
|
||
let spe_cfg0 = Input::new(dp.PC8, Pull::None);
|
||
let spe_cfg1 = Input::new(dp.PC9, Pull::None);
|
||
let _spe_ts_capt = Output::new(dp.PC6, Level::Low, Speed::Low);
|
||
|
||
let spe_int = Input::new(dp.PB11, Pull::None);
|
||
let spe_int = exti::ExtiInput::new(spe_int, dp.EXTI11);
|
||
|
||
let spe_spi_cs_n = Output::new(dp.PB12, Level::High, Speed::High);
|
||
let spe_spi_sclk = dp.PB13;
|
||
let spe_spi_miso = dp.PB14;
|
||
let spe_spi_mosi = dp.PB15;
|
||
|
||
// Don't turn the clock to high, clock must fit within the system clock as we get a runtime panic.
|
||
let mut spi_config = SPI_Config::default();
|
||
spi_config.frequency = Hertz(25_000_000);
|
||
|
||
let spe_spi: SpeSpi = Spi::new(
|
||
dp.SPI2,
|
||
spe_spi_sclk,
|
||
spe_spi_mosi,
|
||
spe_spi_miso,
|
||
dp.DMA1_CH1,
|
||
dp.DMA1_CH2,
|
||
spi_config,
|
||
);
|
||
let spe_spi = SpeSpiCs::new(spe_spi, spe_spi_cs_n, Delay);
|
||
|
||
let cfg0_without_crc = spe_cfg0.is_high();
|
||
let cfg1_spi_mode = spe_cfg1.is_high();
|
||
let uc_cfg1_fcs_en = uc_cfg1.is_low();
|
||
|
||
defmt::println!(
|
||
"ADIN1110: CFG SPI-MODE 1-{}, CRC-bit 0-{} FCS-{}",
|
||
cfg1_spi_mode,
|
||
cfg0_without_crc,
|
||
uc_cfg1_fcs_en
|
||
);
|
||
|
||
// Check the SPI mode selected with the "HW CFG" dip-switch
|
||
if !cfg1_spi_mode {
|
||
error!("Driver doesn´t support SPI Protolcol \"OPEN Alliance\".\nplease use the \"Generic SPI\"! Turn On \"HW CFG\": \"SPI_CFG1\"");
|
||
loop {
|
||
led_uc2_red.toggle();
|
||
Timer::after(Duration::from_hz(10)).await;
|
||
}
|
||
};
|
||
|
||
let state = make_static!(embassy_net_adin1110::State::<8, 8>::new());
|
||
|
||
let (device, runner) = embassy_net_adin1110::new(
|
||
MAC,
|
||
state,
|
||
spe_spi,
|
||
spe_int,
|
||
spe_reset_n,
|
||
!cfg0_without_crc,
|
||
uc_cfg1_fcs_en,
|
||
)
|
||
.await;
|
||
|
||
// Start task blink_led
|
||
unwrap!(spawner.spawn(heartbeat_led(led_uc3_yellow)));
|
||
// Start task temperature measurement
|
||
unwrap!(spawner.spawn(temp_task(temp_sens_i2c, led_uc4_blue)));
|
||
// Start ethernet task
|
||
unwrap!(spawner.spawn(ethernet_task(runner)));
|
||
|
||
let mut rng = Rng::new(dp.RNG, Irqs);
|
||
// Generate random seed
|
||
let seed = rng.next_u64();
|
||
|
||
let ip_cfg = if uc_cfg0.is_low() {
|
||
println!("Waiting for DHCP...");
|
||
let dhcp4_config = embassy_net::DhcpConfig::default();
|
||
embassy_net::Config::dhcpv4(dhcp4_config)
|
||
} else {
|
||
embassy_net::Config::ipv4_static(StaticConfigV4 {
|
||
address: IP_ADDRESS,
|
||
gateway: None,
|
||
dns_servers: Vec::new(),
|
||
})
|
||
};
|
||
|
||
// Init network stack
|
||
let stack = &*make_static!(Stack::new(
|
||
device,
|
||
ip_cfg,
|
||
make_static!(StackResources::<2>::new()),
|
||
seed
|
||
));
|
||
|
||
// Launch network task
|
||
unwrap!(spawner.spawn(net_task(stack)));
|
||
|
||
let cfg = wait_for_config(stack).await;
|
||
let local_addr = cfg.address.address();
|
||
|
||
// Then we can use it!
|
||
let mut rx_buffer = [0; 4096];
|
||
let mut tx_buffer = [0; 4096];
|
||
let mut mb_buf = [0; 4096];
|
||
loop {
|
||
let mut socket = TcpSocket::new(stack, &mut rx_buffer, &mut tx_buffer);
|
||
socket.set_timeout(Some(Duration::from_secs(1)));
|
||
|
||
info!("Listening on http://{}:{}...", local_addr, HTTP_LISTEN_PORT);
|
||
if let Err(e) = socket.accept(HTTP_LISTEN_PORT).await {
|
||
defmt::error!("accept error: {:?}", e);
|
||
continue;
|
||
}
|
||
|
||
loop {
|
||
let _n = match socket.read(&mut mb_buf).await {
|
||
Ok(0) => {
|
||
defmt::info!("read EOF");
|
||
break;
|
||
}
|
||
Ok(n) => n,
|
||
Err(e) => {
|
||
defmt::error!("{:?}", e);
|
||
break;
|
||
}
|
||
};
|
||
led_uc2_red.set_low();
|
||
|
||
let status_line = "HTTP/1.1 200 OK";
|
||
let contents = PAGE;
|
||
let length = contents.len();
|
||
|
||
let _ = write!(
|
||
&mut mb_buf[..],
|
||
"{status_line}\r\nContent-Length: {length}\r\n\r\n{contents}\r\n\0"
|
||
);
|
||
let loc = mb_buf.iter().position(|v| *v == b'#').unwrap();
|
||
|
||
let temp = TEMP.load(Ordering::Relaxed);
|
||
let cel = temp / 1000;
|
||
let mcel = temp % 1000;
|
||
|
||
info!("{}.{}", cel, mcel);
|
||
|
||
let _ = write!(&mut mb_buf[loc..loc + 7], "{cel}.{mcel}");
|
||
|
||
let n = mb_buf.iter().position(|v| *v == 0).unwrap();
|
||
|
||
if let Err(e) = socket.write_all(&mb_buf[..n]).await {
|
||
error!("write error: {:?}", e);
|
||
break;
|
||
}
|
||
|
||
led_uc2_red.set_high();
|
||
}
|
||
}
|
||
}
|
||
|
||
async fn wait_for_config(stack: &'static Stack<Device<'static>>) -> embassy_net::StaticConfigV4 {
|
||
loop {
|
||
if let Some(config) = stack.config_v4() {
|
||
return config;
|
||
}
|
||
yield_now().await;
|
||
}
|
||
}
|
||
|
||
#[embassy_executor::task]
|
||
async fn heartbeat_led(mut led: Output<'static, peripherals::PE6>) {
|
||
let mut tmr = Ticker::every(Duration::from_hz(3));
|
||
loop {
|
||
led.toggle();
|
||
tmr.next().await;
|
||
}
|
||
}
|
||
|
||
// ADT7422
|
||
#[embassy_executor::task]
|
||
async fn temp_task(temp_dev_i2c: TempSensI2c, mut led: Output<'static, peripherals::PG15>) -> ! {
|
||
let mut tmr = Ticker::every(Duration::from_hz(1));
|
||
let mut temp_sens = ADT7422::new(temp_dev_i2c, 0x48).unwrap();
|
||
|
||
loop {
|
||
led.set_low();
|
||
match select(temp_sens.read_temp(), Timer::after_millis(500)).await {
|
||
Either::First(i2c_ret) => match i2c_ret {
|
||
Ok(value) => {
|
||
led.set_high();
|
||
let temp = i32::from(value);
|
||
println!("TEMP: {:04x}, {}", temp, temp * 78 / 10);
|
||
TEMP.store(temp * 78 / 10, Ordering::Relaxed);
|
||
}
|
||
Err(e) => defmt::println!("ADT7422: {}", e),
|
||
},
|
||
Either::Second(_) => println!("Timeout"),
|
||
}
|
||
|
||
tmr.next().await;
|
||
}
|
||
}
|
||
|
||
#[embassy_executor::task]
|
||
async fn ethernet_task(runner: Runner<'static, SpeSpiCs, SpeInt, SpeRst>) -> ! {
|
||
runner.run().await
|
||
}
|
||
|
||
#[embassy_executor::task]
|
||
async fn net_task(stack: &'static Stack<Device<'static>>) -> ! {
|
||
stack.run().await
|
||
}
|
||
|
||
// same panicking *behavior* as `panic-probe` but doesn't print a panic message
|
||
// this prevents the panic message being printed *twice* when `defmt::panic` is invoked
|
||
#[defmt::panic_handler]
|
||
fn panic() -> ! {
|
||
cortex_m::asm::udf()
|
||
}
|
||
|
||
#[allow(non_camel_case_types)]
|
||
#[repr(C)]
|
||
pub enum Registers {
|
||
Temp_MSB = 0x00,
|
||
Temp_LSB,
|
||
Status,
|
||
Cfg,
|
||
T_HIGH_MSB,
|
||
T_HIGH_LSB,
|
||
T_LOW_MSB,
|
||
T_LOW_LSB,
|
||
T_CRIT_MSB,
|
||
T_CRIT_LSB,
|
||
T_HYST,
|
||
ID,
|
||
SW_RESET = 0x2F,
|
||
}
|
||
|
||
pub struct ADT7422<'d, BUS: I2cBus> {
|
||
addr: u8,
|
||
phantom: PhantomData<&'d ()>,
|
||
bus: BUS,
|
||
}
|
||
|
||
#[derive(Debug, Format, PartialEq, Eq)]
|
||
pub enum Error<I2cError: Format> {
|
||
I2c(I2cError),
|
||
Address,
|
||
}
|
||
|
||
impl<'d, BUS> ADT7422<'d, BUS>
|
||
where
|
||
BUS: I2cBus,
|
||
BUS::Error: Format,
|
||
{
|
||
pub fn new(bus: BUS, addr: u8) -> Result<Self, Error<BUS::Error>> {
|
||
if !(0x48..=0x4A).contains(&addr) {
|
||
return Err(Error::Address);
|
||
}
|
||
|
||
Ok(Self {
|
||
bus,
|
||
phantom: PhantomData,
|
||
addr,
|
||
})
|
||
}
|
||
|
||
pub async fn init(&mut self) -> Result<(), Error<BUS::Error>> {
|
||
let mut cfg = 0b000_0000;
|
||
// if self.int.is_some() {
|
||
// // Set 1 SPS mode
|
||
// cfg |= 0b10 << 5;
|
||
// } else {
|
||
// One shot mode
|
||
cfg |= 0b01 << 5;
|
||
// }
|
||
|
||
self.write_cfg(cfg).await
|
||
}
|
||
|
||
pub async fn read(&mut self, reg: Registers) -> Result<u8, Error<BUS::Error>> {
|
||
let mut buffer = [0u8; 1];
|
||
self.bus
|
||
.write_read(self.addr, &[reg as u8], &mut buffer)
|
||
.await
|
||
.map_err(Error::I2c)?;
|
||
Ok(buffer[0])
|
||
}
|
||
|
||
pub async fn write_cfg(&mut self, cfg: u8) -> Result<(), Error<BUS::Error>> {
|
||
let buf = [Registers::Cfg as u8, cfg];
|
||
self.bus.write(self.addr, &buf).await.map_err(Error::I2c)
|
||
}
|
||
|
||
pub async fn read_temp(&mut self) -> Result<i16, Error<BUS::Error>> {
|
||
let mut buffer = [0u8; 2];
|
||
|
||
// if let Some(int) = &mut self.int {
|
||
// // Wait for interrupt
|
||
// int.wait_for_low().await.unwrap();
|
||
// } else {
|
||
// Start: One shot
|
||
let cfg = 0b01 << 5;
|
||
self.write_cfg(cfg).await?;
|
||
Timer::after_millis(250).await;
|
||
self.bus
|
||
.write_read(self.addr, &[Registers::Temp_MSB as u8], &mut buffer)
|
||
.await
|
||
.map_err(Error::I2c)?;
|
||
Ok(i16::from_be_bytes(buffer))
|
||
}
|
||
}
|
||
|
||
// Web page
|
||
const PAGE: &str = r#"<!DOCTYPE html>
|
||
<html lang="en">
|
||
<head>
|
||
<meta charset="utf-8">
|
||
<meta http-equiv="refresh" content="1" >
|
||
<title>ADIN1110 with Rust</title>
|
||
</head>
|
||
<body>
|
||
<p>EVAL-ADIN1110EBZ</p>
|
||
<table><td>Temp Sensor ADT7422:</td><td> #00.00 °C</td></table>
|
||
</body>
|
||
</html>"#;
|