Merge pull request #2074 from embassy-rs/rcc-no-spaghetti

time: add `links` key, release v0.1.5.

README.md

@@ -62,9 +62,9 @@ async fn blink(pin: AnyPin) {
     loop {
         // Timekeeping is globally available, no need to mess with hardware timers.
         led.set_high();
-        Timer::after(Duration::from_millis(150)).await;
+        Timer::after_millis(150).await;
         led.set_low();
-        Timer::after(Duration::from_millis(150)).await;
+        Timer::after_millis(150).await;
     }
 }
 

cyw43/Cargo.toml

@@ -11,7 +11,7 @@ log = ["dep:log"]
 firmware-logs = []
 
 [dependencies]
-embassy-time = { version = "0.1.4", path = "../embassy-time"}
+embassy-time = { version = "0.1.5", path = "../embassy-time"}
 embassy-sync = { version = "0.3.0", path = "../embassy-sync"}
 embassy-futures = { version = "0.1.0", path = "../embassy-futures"}
 embassy-net-driver-channel = { version = "0.1.0", path = "../embassy-net-driver-channel"}

cyw43/src/bus.rs

@@ -1,5 +1,5 @@
 use embassy_futures::yield_now;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use embedded_hal_1::digital::OutputPin;
 use futures::FutureExt;
 
@@ -51,9 +51,9 @@ where
     pub async fn init(&mut self) {
         // Reset
         self.pwr.set_low().unwrap();
-        Timer::after(Duration::from_millis(20)).await;
+        Timer::after_millis(20).await;
         self.pwr.set_high().unwrap();
-        Timer::after(Duration::from_millis(250)).await;
+        Timer::after_millis(250).await;
 
         while self
             .read32_swapped(REG_BUS_TEST_RO)

cyw43/src/control.rs

@@ -2,7 +2,7 @@ use core::cmp::{max, min};
 
 use ch::driver::LinkState;
 use embassy_net_driver_channel as ch;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 
 pub use crate::bus::SpiBusCyw43;
 use crate::consts::*;
@@ -87,22 +87,22 @@ impl<'a> Control<'a> {
         self.set_iovar("country", &country_info.to_bytes()).await;
 
         // set country takes some time, next ioctls fail if we don't wait.
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
 
         // Set antenna to chip antenna
         self.ioctl_set_u32(IOCTL_CMD_ANTDIV, 0, 0).await;
 
         self.set_iovar_u32("bus:txglom", 0).await;
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
         //self.set_iovar_u32("apsta", 1).await; // this crashes, also we already did it before...??
-        //Timer::after(Duration::from_millis(100)).await;
+        //Timer::after_millis(100).await;
         self.set_iovar_u32("ampdu_ba_wsize", 8).await;
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
         self.set_iovar_u32("ampdu_mpdu", 4).await;
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
         //self.set_iovar_u32("ampdu_rx_factor", 0).await; // this crashes
 
-        //Timer::after(Duration::from_millis(100)).await;
+        //Timer::after_millis(100).await;
 
         // evts
         let mut evts = EventMask {
@@ -121,17 +121,17 @@ impl<'a> Control<'a> {
 
         self.set_iovar("bsscfg:event_msgs", &evts.to_bytes()).await;
 
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
 
         // set wifi up
         self.up().await;
 
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
 
         self.ioctl_set_u32(110, 0, 1).await; // SET_GMODE = auto
         self.ioctl_set_u32(142, 0, 0).await; // SET_BAND = any
 
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
 
         self.state_ch.set_ethernet_address(mac_addr);
 
@@ -185,7 +185,7 @@ impl<'a> Control<'a> {
         self.set_iovar_u32x2("bsscfg:sup_wpa2_eapver", 0, 0xFFFF_FFFF).await;
         self.set_iovar_u32x2("bsscfg:sup_wpa_tmo", 0, 2500).await;
 
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
 
         let mut pfi = PassphraseInfo {
             len: passphrase.len() as _,
@@ -297,7 +297,7 @@ impl<'a> Control<'a> {
         if security != Security::OPEN {
             self.set_iovar_u32x2("bsscfg:wpa_auth", 0, 0x0084).await; // wpa_auth = WPA2_AUTH_PSK | WPA_AUTH_PSK
 
-            Timer::after(Duration::from_millis(100)).await;
+            Timer::after_millis(100).await;
 
             // Set passphrase
             let mut pfi = PassphraseInfo {

cyw43/src/runner.rs

@@ -555,14 +555,14 @@ where
 
         self.bus.bp_write8(base + AI_RESETCTRL_OFFSET, 0).await;
 
-        Timer::after(Duration::from_millis(1)).await;
+        Timer::after_millis(1).await;
 
         self.bus
             .bp_write8(base + AI_IOCTRL_OFFSET, AI_IOCTRL_BIT_CLOCK_EN)
             .await;
         let _ = self.bus.bp_read8(base + AI_IOCTRL_OFFSET).await;
 
-        Timer::after(Duration::from_millis(1)).await;
+        Timer::after_millis(1).await;
     }
 
     async fn core_is_up(&mut self, core: Core) -> bool {

docs/modules/ROOT/pages/runtime.adoc

@@ -6,7 +6,7 @@ The Embassy executor is an async/await executor designed for embedded usage alon
 
 * No `alloc`, no heap needed. Task are statically allocated.
 * No "fixed capacity" data structures, executor works with 1 or 1000 tasks without needing config/tuning.
-* Integrated timer queue: sleeping is easy, just do `Timer::after(Duration::from_secs(1)).await;`.
+* Integrated timer queue: sleeping is easy, just do `Timer::after_secs(1).await;`.
 * No busy-loop polling: CPU sleeps when there's no work to do, using interrupts or `WFE/SEV`.
 * Efficient polling: a wake will only poll the woken task, not all of them.
 * Fair: a task can't monopolize CPU time even if it's constantly being woken. All other tasks get a chance to run before a given task gets polled for the second time.

embassy-embedded-hal/Cargo.toml

@@ -21,7 +21,7 @@ default = ["time"]
 [dependencies]
 embassy-futures = { version = "0.1.0", path = "../embassy-futures", optional = true }
 embassy-sync = { version = "0.3.0", path = "../embassy-sync" }
-embassy-time = { version = "0.1.4", path = "../embassy-time", optional = true }
+embassy-time = { version = "0.1.5", path = "../embassy-time", optional = true }
 embedded-hal-02 = { package = "embedded-hal", version = "0.2.6", features = [
     "unproven",
 ] }

embassy-embedded-hal/src/shared_bus/asynch/spi.rs

@@ -76,9 +76,7 @@ where
                     #[cfg(not(feature = "time"))]
                     Operation::DelayUs(_) => return Err(SpiDeviceError::DelayUsNotSupported),
                     #[cfg(feature = "time")]
-                    Operation::DelayUs(us) => {
+                    Operation::DelayUs(us) => embassy_time::Timer::after_micros(*us as _).await,
-                        embassy_time::Timer::after(embassy_time::Duration::from_micros(*us as _)).await
-                    }
                 }
             }
         };
@@ -143,9 +141,7 @@ where
                     #[cfg(not(feature = "time"))]
                     Operation::DelayUs(_) => return Err(SpiDeviceError::DelayUsNotSupported),
                     #[cfg(feature = "time")]
-                    Operation::DelayUs(us) => {
+                    Operation::DelayUs(us) => embassy_time::Timer::after_micros(*us as _).await,
-                        embassy_time::Timer::after(embassy_time::Duration::from_micros(*us as _)).await
-                    }
                 }
             }
         };

embassy-executor/Cargo.toml

@@ -59,7 +59,7 @@ rtos-trace = { version = "0.1.2", optional = true }
 
 futures-util = { version = "0.3.17", default-features = false }
 embassy-macros = { version = "0.2.1", path = "../embassy-macros" }
-embassy-time = { version = "0.1.4", path = "../embassy-time", optional = true}
+embassy-time = { version = "0.1.5", path = "../embassy-time", optional = true}
 atomic-polyfill = "1.0.1"
 critical-section = "1.1"
 static_cell = "1.1"

embassy-executor/README.md

@@ -4,7 +4,7 @@ An async/await executor designed for embedded usage.
 
 - No `alloc`, no heap needed. Task futures are statically allocated.
 - No "fixed capacity" data structures, executor works with 1 or 1000 tasks without needing config/tuning.
-- Integrated timer queue: sleeping is easy, just do `Timer::after(Duration::from_secs(1)).await;`.
+- Integrated timer queue: sleeping is easy, just do `Timer::after_secs(1).await;`.
 - No busy-loop polling: CPU sleeps when there's no work to do, using interrupts or `WFE/SEV`.
 - Efficient polling: a wake will only poll the woken task, not all of them.
 - Fair: a task can't monopolize CPU time even if it's constantly being woken. All other tasks get a chance to run before a given task gets polled for the second time.

embassy-hal-internal/README.md

@@ -1,4 +1,4 @@
-# embassy-macros
+# embassy-hal-internal
 
 An [Embassy](https://embassy.dev) project.
 

embassy-hal-internal/src/lib.rs

@@ -10,7 +10,6 @@ pub mod drop;
 mod macros;
 mod peripheral;
 pub mod ratio;
-pub mod ring_buffer;
 pub use peripheral::{Peripheral, PeripheralRef};
 
 #[cfg(feature = "cortex-m")]

embassy-hal-internal/src/ring_buffer.rs

@@ -1,136 +0,0 @@
-pub struct RingBuffer<'a> {
-    buf: &'a mut [u8],
-    start: usize,
-    end: usize,
-    empty: bool,
-}
-
-impl<'a> RingBuffer<'a> {
-    pub fn new(buf: &'a mut [u8]) -> Self {
-        Self {
-            buf,
-            start: 0,
-            end: 0,
-            empty: true,
-        }
-    }
-
-    pub fn push_buf(&mut self) -> &mut [u8] {
-        if self.start == self.end && !self.empty {
-            trace!("  ringbuf: push_buf empty");
-            return &mut self.buf[..0];
-        }
-
-        let n = if self.start <= self.end {
-            self.buf.len() - self.end
-        } else {
-            self.start - self.end
-        };
-
-        trace!("  ringbuf: push_buf {:?}..{:?}", self.end, self.end + n);
-        &mut self.buf[self.end..self.end + n]
-    }
-
-    pub fn push(&mut self, n: usize) {
-        trace!("  ringbuf: push {:?}", n);
-        if n == 0 {
-            return;
-        }
-
-        self.end = self.wrap(self.end + n);
-        self.empty = false;
-    }
-
-    pub fn pop_buf(&mut self) -> &mut [u8] {
-        if self.empty {
-            trace!("  ringbuf: pop_buf empty");
-            return &mut self.buf[..0];
-        }
-
-        let n = if self.end <= self.start {
-            self.buf.len() - self.start
-        } else {
-            self.end - self.start
-        };
-
-        trace!("  ringbuf: pop_buf {:?}..{:?}", self.start, self.start + n);
-        &mut self.buf[self.start..self.start + n]
-    }
-
-    pub fn pop(&mut self, n: usize) {
-        trace!("  ringbuf: pop {:?}", n);
-        if n == 0 {
-            return;
-        }
-
-        self.start = self.wrap(self.start + n);
-        self.empty = self.start == self.end;
-    }
-
-    pub fn is_full(&self) -> bool {
-        self.start == self.end && !self.empty
-    }
-
-    pub fn is_empty(&self) -> bool {
-        self.empty
-    }
-
-    pub fn clear(&mut self) {
-        self.start = 0;
-        self.end = 0;
-        self.empty = true;
-    }
-
-    fn wrap(&self, n: usize) -> usize {
-        assert!(n <= self.buf.len());
-        if n == self.buf.len() {
-            0
-        } else {
-            n
-        }
-    }
-}
-
-#[cfg(test)]
-mod tests {
-    use super::*;
-
-    #[test]
-    fn push_pop() {
-        let mut b = [0; 4];
-        let mut rb = RingBuffer::new(&mut b);
-        let buf = rb.push_buf();
-        assert_eq!(4, buf.len());
-        buf[0] = 1;
-        buf[1] = 2;
-        buf[2] = 3;
-        buf[3] = 4;
-        rb.push(4);
-
-        let buf = rb.pop_buf();
-        assert_eq!(4, buf.len());
-        assert_eq!(1, buf[0]);
-        rb.pop(1);
-
-        let buf = rb.pop_buf();
-        assert_eq!(3, buf.len());
-        assert_eq!(2, buf[0]);
-        rb.pop(1);
-
-        let buf = rb.pop_buf();
-        assert_eq!(2, buf.len());
-        assert_eq!(3, buf[0]);
-        rb.pop(1);
-
-        let buf = rb.pop_buf();
-        assert_eq!(1, buf.len());
-        assert_eq!(4, buf[0]);
-        rb.pop(1);
-
-        let buf = rb.pop_buf();
-        assert_eq!(0, buf.len());
-
-        let buf = rb.push_buf();
-        assert_eq!(4, buf.len());
-    }
-}

embassy-lora/Cargo.toml

@@ -20,7 +20,7 @@ defmt = ["dep:defmt", "lorawan-device/defmt"]
 defmt = { version = "0.3", optional = true }
 log = { version = "0.4.14", optional = true }
 
-embassy-time = { version = "0.1.4", path = "../embassy-time", optional = true }
+embassy-time = { version = "0.1.5", path = "../embassy-time", optional = true }
 embassy-sync = { version = "0.3.0", path = "../embassy-sync" }
 embassy-stm32 = { version = "0.1.0", path = "../embassy-stm32", default-features = false, optional = true }
 embedded-hal-async = { version = "=1.0.0-rc.1" }

embassy-lora/src/lib.rs

@@ -34,6 +34,6 @@ impl lorawan_device::async_device::radio::Timer for LoraTimer {
     }
 
     async fn delay_ms(&mut self, millis: u64) {
-        Timer::after(Duration::from_millis(millis)).await
+        Timer::after_millis(millis).await
     }
 }

embassy-net-adin1110/Cargo.toml

@@ -17,7 +17,7 @@ embedded-hal-1 = { package = "embedded-hal", version = "=1.0.0-rc.1" }
 embedded-hal-async = { version = "=1.0.0-rc.1" }
 embedded-hal-bus = { version = "=0.1.0-rc.1", features = ["async"] }
 embassy-net-driver-channel = { version = "0.1.0", path = "../embassy-net-driver-channel" }
-embassy-time = { version = "0.1.4", path = "../embassy-time" }
+embassy-time = { version = "0.1.5", path = "../embassy-time" }
 embassy-futures = { version = "0.1.0", path = "../embassy-futures" }
 bitfield = "0.14.0"
 

embassy-net-adin1110/src/lib.rs

@@ -20,7 +20,7 @@ pub use crc32::ETH_FCS;
 use crc8::crc8;
 use embassy_futures::select::{select, Either};
 use embassy_net_driver_channel as ch;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use embedded_hal_1::digital::OutputPin;
 use embedded_hal_async::digital::Wait;
 use embedded_hal_async::spi::{Error, Operation, SpiDevice};
@@ -609,12 +609,12 @@ pub async fn new<const N_RX: usize, const N_TX: usize, SPI: SpiDevice, INT: Wait
     reset.set_low().unwrap();
 
     // Wait t1: 20-43mS
-    Timer::after(Duration::from_millis(30)).await;
+    Timer::after_millis(30).await;
 
     reset.set_high().unwrap();
 
     // Wait t3: 50mS
-    Timer::after(Duration::from_millis(50)).await;
+    Timer::after_millis(50).await;
 
     // Create device
     let mut mac = ADIN1110::new(spi_dev, spi_crc, append_fcs_on_tx);

embassy-net-enc28j60/Cargo.toml

@@ -11,7 +11,7 @@ edition = "2021"
 embedded-hal = { version = "1.0.0-rc.1" }
 embedded-hal-async = { version = "=1.0.0-rc.1" }
 embassy-net-driver = { version = "0.1.0", path = "../embassy-net-driver" }
-embassy-time = { version = "0.1.4", path = "../embassy-time" }
+embassy-time = { version = "0.1.5", path = "../embassy-time" }
 embassy-futures = { version = "0.1.0", path = "../embassy-futures" }
 
 defmt = { version = "0.3", optional = true }

embassy-net-esp-hosted/Cargo.toml

@@ -7,7 +7,7 @@ edition = "2021"
 defmt = { version = "0.3", optional = true }
 log = { version = "0.4.14", optional = true }
 
-embassy-time = { version = "0.1.4", path = "../embassy-time" }
+embassy-time = { version = "0.1.5", path = "../embassy-time" }
 embassy-sync = { version = "0.3.0", path = "../embassy-sync"}
 embassy-futures = { version = "0.1.0", path = "../embassy-futures"}
 embassy-net-driver-channel = { version = "0.1.0", path = "../embassy-net-driver-channel"}

embassy-net-esp-hosted/src/lib.rs

@@ -169,9 +169,9 @@ where
     pub async fn run(mut self) -> ! {
         debug!("resetting...");
         self.reset.set_low().unwrap();
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
         self.reset.set_high().unwrap();
-        Timer::after(Duration::from_millis(1000)).await;
+        Timer::after_millis(1000).await;
 
         let mut tx_buf = [0u8; MAX_SPI_BUFFER_SIZE];
         let mut rx_buf = [0u8; MAX_SPI_BUFFER_SIZE];

embassy-net-wiznet/Cargo.toml

@@ -11,7 +11,7 @@ edition = "2021"
 embedded-hal = { version = "1.0.0-rc.1" }
 embedded-hal-async = { version = "=1.0.0-rc.1" }
 embassy-net-driver-channel = { version = "0.1.0", path = "../embassy-net-driver-channel" }
-embassy-time = { version = "0.1.4", path = "../embassy-time" }
+embassy-time = { version = "0.1.5", path = "../embassy-time" }
 embassy-futures = { version = "0.1.0", path = "../embassy-futures" }
 defmt = { version = "0.3", optional = true }
 

embassy-net-wiznet/src/lib.rs

@@ -8,7 +8,7 @@ mod device;
 use embassy_futures::select::{select, Either};
 use embassy_net_driver_channel as ch;
 use embassy_net_driver_channel::driver::LinkState;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use embedded_hal::digital::OutputPin;
 use embedded_hal_async::digital::Wait;
 use embedded_hal_async::spi::SpiDevice;
@@ -95,12 +95,12 @@ pub async fn new<'a, const N_RX: usize, const N_TX: usize, C: Chip, SPI: SpiDevi
     // Reset the chip.
     reset.set_low().ok();
     // Ensure the reset is registered.
-    Timer::after(Duration::from_millis(1)).await;
+    Timer::after_millis(1).await;
     reset.set_high().ok();
 
     // Wait for PLL lock. Some chips are slower than others.
     // Slowest is w5100s which is 100ms, so let's just wait that.
-    Timer::after(Duration::from_millis(100)).await;
+    Timer::after_millis(100).await;
 
     let mac = WiznetDevice::new(spi_dev, mac_addr).await.unwrap();
 

embassy-net/Cargo.toml

@@ -52,7 +52,7 @@ smoltcp = { version = "0.10.0", default-features = false, features = [
 ] }
 
 embassy-net-driver = { version = "0.1.0", path = "../embassy-net-driver" }
-embassy-time = { version = "0.1.4", path = "../embassy-time" }
+embassy-time = { version = "0.1.5", path = "../embassy-time" }
 embassy-sync = { version = "0.3.0", path = "../embassy-sync" }
 embedded-io-async = { version = "0.6.0", optional = true }
 

embassy-net/src/lib.rs

@@ -509,7 +509,10 @@ impl<D: Driver> Stack<D> {
             self.with_mut(|s, i| {
                 let socket = s.sockets.get_mut::<dns::Socket>(i.dns_socket);
                 match socket.start_query(s.iface.context(), name, qtype) {
-                    Ok(handle) => Poll::Ready(Ok(handle)),
+                    Ok(handle) => {
+                        s.waker.wake();
+                        Poll::Ready(Ok(handle))
+                    }
                     Err(dns::StartQueryError::NoFreeSlot) => {
                         i.dns_waker.register(cx.waker());
                         Poll::Pending

embassy-nrf/Cargo.toml

@@ -94,7 +94,7 @@ _gpio-p1 = []
 _nrf52832_anomaly_109 = []
 
 [dependencies]
-embassy-time = { version = "0.1.4", path = "../embassy-time", optional = true }
+embassy-time = { version = "0.1.5", path = "../embassy-time", optional = true }
 embassy-sync = { version = "0.3.0", path = "../embassy-sync" }
 embassy-hal-internal = {version = "0.1.0", path = "../embassy-hal-internal", features = ["cortex-m", "prio-bits-3"] }
 embassy-embedded-hal = {version = "0.1.0", path = "../embassy-embedded-hal" }

embassy-nrf/src/chips/nrf5340_app.rs

@@ -6,10 +6,13 @@ pub mod pac {
     // To avoid cfg spam, we remove _ns or _s suffixes here.
 
     pub use nrf5340_app_pac::NVIC_PRIO_BITS;
-    
+
+    #[cfg(feature="rt")]
+    #[doc(no_inline)]
+    pub use nrf5340_app_pac::interrupt;
+
     #[doc(no_inline)]
     pub use nrf5340_app_pac::{
-        interrupt,
         Interrupt,
         Peripherals,
 
@@ -60,156 +63,167 @@ pub mod pac {
         wdt0_ns as wdt0,
     };
     
-    #[cfg(feature = "nrf5340-app-ns")]
+    /// Non-Secure mode (NS) peripherals
-    #[doc(no_inline)]
+    pub mod ns {
-    pub use nrf5340_app_pac::{
+        #[cfg(feature = "nrf5340-app-ns")]
-        CLOCK_NS as CLOCK,
+        #[doc(no_inline)]
-        COMP_NS as COMP,
+        pub use nrf5340_app_pac::{
-        CTRLAP_NS as CTRLAP,
+            CLOCK_NS as CLOCK,
-        DCNF_NS as DCNF,
+            COMP_NS as COMP,
-        DPPIC_NS as DPPIC,
+            CTRLAP_NS as CTRLAP,
-        EGU0_NS as EGU0,
+            DCNF_NS as DCNF,
-        EGU1_NS as EGU1,
+            DPPIC_NS as DPPIC,
-        EGU2_NS as EGU2,
+            EGU0_NS as EGU0,
-        EGU3_NS as EGU3,
+            EGU1_NS as EGU1,
-        EGU4_NS as EGU4,
+            EGU2_NS as EGU2,
-        EGU5_NS as EGU5,
+            EGU3_NS as EGU3,
-        FPU_NS as FPU,
+            EGU4_NS as EGU4,
-        GPIOTE1_NS as GPIOTE1,
+            EGU5_NS as EGU5,
-        I2S0_NS as I2S0,
+            FPU_NS as FPU,
-        IPC_NS as IPC,
+            GPIOTE1_NS as GPIOTE1,
-        KMU_NS as KMU,
+            I2S0_NS as I2S0,
-        LPCOMP_NS as LPCOMP,
+            IPC_NS as IPC,
-        MUTEX_NS as MUTEX,
+            KMU_NS as KMU,
-        NFCT_NS as NFCT,
+            LPCOMP_NS as LPCOMP,
-        NVMC_NS as NVMC,
+            MUTEX_NS as MUTEX,
-        OSCILLATORS_NS as OSCILLATORS,
+            NFCT_NS as NFCT,
-        P0_NS as P0,
+            NVMC_NS as NVMC,
-        P1_NS as P1,
+            OSCILLATORS_NS as OSCILLATORS,
-        PDM0_NS as PDM0,
+            P0_NS as P0,
-        POWER_NS as POWER,
+            P1_NS as P1,
-        PWM0_NS as PWM0,
+            PDM0_NS as PDM0,
-        PWM1_NS as PWM1,
+            POWER_NS as POWER,
-        PWM2_NS as PWM2,
+            PWM0_NS as PWM0,
-        PWM3_NS as PWM3,
+            PWM1_NS as PWM1,
-        QDEC0_NS as QDEC0,
+            PWM2_NS as PWM2,
-        QDEC1_NS as QDEC1,
+            PWM3_NS as PWM3,
-        QSPI_NS as QSPI,
+            QDEC0_NS as QDEC0,
-        REGULATORS_NS as REGULATORS,
+            QDEC1_NS as QDEC1,
-        RESET_NS as RESET,
+            QSPI_NS as QSPI,
-        RTC0_NS as RTC0,
+            REGULATORS_NS as REGULATORS,
-        RTC1_NS as RTC1,
+            RESET_NS as RESET,
-        SAADC_NS as SAADC,
+            RTC0_NS as RTC0,
-        SPIM0_NS as SPIM0,
+            RTC1_NS as RTC1,
-        SPIM1_NS as SPIM1,
+            SAADC_NS as SAADC,
-        SPIM2_NS as SPIM2,
+            SPIM0_NS as SPIM0,
-        SPIM3_NS as SPIM3,
+            SPIM1_NS as SPIM1,
-        SPIM4_NS as SPIM4,
+            SPIM2_NS as SPIM2,
-        SPIS0_NS as SPIS0,
+            SPIM3_NS as SPIM3,
-        SPIS1_NS as SPIS1,
+            SPIM4_NS as SPIM4,
-        SPIS2_NS as SPIS2,
+            SPIS0_NS as SPIS0,
-        SPIS3_NS as SPIS3,
+            SPIS1_NS as SPIS1,
-        TIMER0_NS as TIMER0,
+            SPIS2_NS as SPIS2,
-        TIMER1_NS as TIMER1,
+            SPIS3_NS as SPIS3,
-        TIMER2_NS as TIMER2,
+            TIMER0_NS as TIMER0,
-        TWIM0_NS as TWIM0,
+            TIMER1_NS as TIMER1,
-        TWIM1_NS as TWIM1,
+            TIMER2_NS as TIMER2,
-        TWIM2_NS as TWIM2,
+            TWIM0_NS as TWIM0,
-        TWIM3_NS as TWIM3,
+            TWIM1_NS as TWIM1,
-        TWIS0_NS as TWIS0,
+            TWIM2_NS as TWIM2,
-        TWIS1_NS as TWIS1,
+            TWIM3_NS as TWIM3,
-        TWIS2_NS as TWIS2,
+            TWIS0_NS as TWIS0,
-        TWIS3_NS as TWIS3,
+            TWIS1_NS as TWIS1,
-        UARTE0_NS as UARTE0,
+            TWIS2_NS as TWIS2,
-        UARTE1_NS as UARTE1,
+            TWIS3_NS as TWIS3,
-        UARTE2_NS as UARTE2,
+            UARTE0_NS as UARTE0,
-        UARTE3_NS as UARTE3,
+            UARTE1_NS as UARTE1,
-        USBD_NS as USBD,
+            UARTE2_NS as UARTE2,
-        USBREGULATOR_NS as USBREGULATOR,
+            UARTE3_NS as UARTE3,
-        VMC_NS as VMC,
+            USBD_NS as USBD,
-        WDT0_NS as WDT0,
+            USBREGULATOR_NS as USBREGULATOR,
-        WDT1_NS as WDT1,
+            VMC_NS as VMC,
-    };
+            WDT0_NS as WDT0,
+            WDT1_NS as WDT1,
+        };
+    }
 
-    #[cfg(feature = "nrf5340-app-s")]
+    /// Secure mode (S) peripherals
-    #[doc(no_inline)]
+    pub mod s {
-    pub use nrf5340_app_pac::{
+        #[cfg(feature = "nrf5340-app-s")]
-        CACHEDATA_S as CACHEDATA,
+        #[doc(no_inline)]
-        CACHEINFO_S as CACHEINFO,
+        pub use nrf5340_app_pac::{
-        CACHE_S as CACHE,
+            CACHEDATA_S as CACHEDATA,
-        CLOCK_S as CLOCK,
+            CACHEINFO_S as CACHEINFO,
-        COMP_S as COMP,
+            CACHE_S as CACHE,
-        CRYPTOCELL_S as CRYPTOCELL,
+            CLOCK_S as CLOCK,
-        CTI_S as CTI,
+            COMP_S as COMP,
-        CTRLAP_S as CTRLAP,
+            CRYPTOCELL_S as CRYPTOCELL,
-        DCNF_S as DCNF,
+            CTI_S as CTI,
-        DPPIC_S as DPPIC,
+            CTRLAP_S as CTRLAP,
-        EGU0_S as EGU0,
+            DCNF_S as DCNF,
-        EGU1_S as EGU1,
+            DPPIC_S as DPPIC,
-        EGU2_S as EGU2,
+            EGU0_S as EGU0,
-        EGU3_S as EGU3,
+            EGU1_S as EGU1,
-        EGU4_S as EGU4,
+            EGU2_S as EGU2,
-        EGU5_S as EGU5,
+            EGU3_S as EGU3,
-        FICR_S as FICR,
+            EGU4_S as EGU4,
-        FPU_S as FPU,
+            EGU5_S as EGU5,
-        GPIOTE0_S as GPIOTE0,
+            FICR_S as FICR,
-        I2S0_S as I2S0,
+            FPU_S as FPU,
-        IPC_S as IPC,
+            GPIOTE0_S as GPIOTE0,
-        KMU_S as KMU,
+            I2S0_S as I2S0,
-        LPCOMP_S as LPCOMP,
+            IPC_S as IPC,
-        MUTEX_S as MUTEX,
+            KMU_S as KMU,
-        NFCT_S as NFCT,
+            LPCOMP_S as LPCOMP,
-        NVMC_S as NVMC,
+            MUTEX_S as MUTEX,
-        OSCILLATORS_S as OSCILLATORS,
+            NFCT_S as NFCT,
-        P0_S as P0,
+            NVMC_S as NVMC,
-        P1_S as P1,
+            OSCILLATORS_S as OSCILLATORS,
-        PDM0_S as PDM0,
+            P0_S as P0,
-        POWER_S as POWER,
+            P1_S as P1,
-        PWM0_S as PWM0,
+            PDM0_S as PDM0,
-        PWM1_S as PWM1,
+            POWER_S as POWER,
-        PWM2_S as PWM2,
+            PWM0_S as PWM0,
-        PWM3_S as PWM3,
+            PWM1_S as PWM1,
-        QDEC0_S as QDEC0,
+            PWM2_S as PWM2,
-        QDEC1_S as QDEC1,
+            PWM3_S as PWM3,
-        QSPI_S as QSPI,
+            QDEC0_S as QDEC0,
-        REGULATORS_S as REGULATORS,
+            QDEC1_S as QDEC1,
-        RESET_S as RESET,
+            QSPI_S as QSPI,
-        RTC0_S as RTC0,
+            REGULATORS_S as REGULATORS,
-        RTC1_S as RTC1,
+            RESET_S as RESET,
-        SAADC_S as SAADC,
+            RTC0_S as RTC0,
-        SPIM0_S as SPIM0,
+            RTC1_S as RTC1,
-        SPIM1_S as SPIM1,
+            SAADC_S as SAADC,
-        SPIM2_S as SPIM2,
+            SPIM0_S as SPIM0,
-        SPIM3_S as SPIM3,
+            SPIM1_S as SPIM1,
-        SPIM4_S as SPIM4,
+            SPIM2_S as SPIM2,
-        SPIS0_S as SPIS0,
+            SPIM3_S as SPIM3,
-        SPIS1_S as SPIS1,
+            SPIM4_S as SPIM4,
-        SPIS2_S as SPIS2,
+            SPIS0_S as SPIS0,
-        SPIS3_S as SPIS3,
+            SPIS1_S as SPIS1,
-        SPU_S as SPU,
+            SPIS2_S as SPIS2,
-        TAD_S as TAD,
+            SPIS3_S as SPIS3,
-        TIMER0_S as TIMER0,
+            SPU_S as SPU,
-        TIMER1_S as TIMER1,
+            TAD_S as TAD,
-        TIMER2_S as TIMER2,
+            TIMER0_S as TIMER0,
-        TWIM0_S as TWIM0,
+            TIMER1_S as TIMER1,
-        TWIM1_S as TWIM1,
+            TIMER2_S as TIMER2,
-        TWIM2_S as TWIM2,
+            TWIM0_S as TWIM0,
-        TWIM3_S as TWIM3,
+            TWIM1_S as TWIM1,
-        TWIS0_S as TWIS0,
+            TWIM2_S as TWIM2,
-        TWIS1_S as TWIS1,
+            TWIM3_S as TWIM3,
-        TWIS2_S as TWIS2,
+            TWIS0_S as TWIS0,
-        TWIS3_S as TWIS3,
+            TWIS1_S as TWIS1,
-        UARTE0_S as UARTE0,
+            TWIS2_S as TWIS2,
-        UARTE1_S as UARTE1,
+            TWIS3_S as TWIS3,
-        UARTE2_S as UARTE2,
+            UARTE0_S as UARTE0,
-        UARTE3_S as UARTE3,
+            UARTE1_S as UARTE1,
-        UICR_S as UICR,
+            UARTE2_S as UARTE2,
-        USBD_S as USBD,
+            UARTE3_S as UARTE3,
-        USBREGULATOR_S as USBREGULATOR,
+            UICR_S as UICR,
-        VMC_S as VMC,
+            USBD_S as USBD,
-        WDT0_S as WDT0,
+            USBREGULATOR_S as USBREGULATOR,
-        WDT1_S as WDT1,
+            VMC_S as VMC,
-    };
+            WDT0_S as WDT0,
+            WDT1_S as WDT1,
+        };
+    }
+
+    #[cfg(feature = "_ns")]
+    pub use ns::*;
+    #[cfg(feature = "_s")]
+    pub use s::*;
 }
 
 /// The maximum buffer size that the EasyDMA can send/recv in one operation.

embassy-nrf/src/chips/nrf5340_net.rs

@@ -7,9 +7,12 @@ pub mod pac {
 
     pub use nrf5340_net_pac::NVIC_PRIO_BITS;
 
+    #[cfg(feature="rt")]
+    #[doc(no_inline)]
+    pub use nrf5340_net_pac::interrupt;
+
     #[doc(no_inline)]
     pub use nrf5340_net_pac::{
-        interrupt,
         Interrupt,
         Peripherals,
 

embassy-nrf/src/chips/nrf9160.rs

@@ -7,9 +7,12 @@ pub mod pac {
 
     pub use nrf9160_pac::NVIC_PRIO_BITS;
 
+    #[cfg(feature="rt")]
+    #[doc(no_inline)]
+    pub use nrf9160_pac::interrupt;
+
     #[doc(no_inline)]
     pub use nrf9160_pac::{
-        interrupt,
         Interrupt,
 
         cc_host_rgf_s as cc_host_rgf,
@@ -45,122 +48,131 @@ pub mod pac {
         wdt_ns as wdt,
     };
     
-    #[cfg(feature = "nrf9160-ns")]
+    /// Non-Secure mode (NS) peripherals
-    #[doc(no_inline)]
+    pub mod ns {
-    pub use nrf9160_pac::{
+        #[doc(no_inline)]
-        CLOCK_NS as CLOCK,
+        pub use nrf9160_pac::{
-        DPPIC_NS as DPPIC,
+            CLOCK_NS as CLOCK,
-        EGU0_NS as EGU0,
+            DPPIC_NS as DPPIC,
-        EGU1_NS as EGU1,
+            EGU0_NS as EGU0,
-        EGU2_NS as EGU2,
+            EGU1_NS as EGU1,
-        EGU3_NS as EGU3,
+            EGU2_NS as EGU2,
-        EGU4_NS as EGU4,
+            EGU3_NS as EGU3,
-        EGU5_NS as EGU5,
+            EGU4_NS as EGU4,
-        FPU_NS as FPU,
+            EGU5_NS as EGU5,
-        GPIOTE1_NS as GPIOTE1,
+            FPU_NS as FPU,
-        I2S_NS as I2S,
+            GPIOTE1_NS as GPIOTE1,
-        IPC_NS as IPC,
+            I2S_NS as I2S,
-        KMU_NS as KMU,
+            IPC_NS as IPC,
-        NVMC_NS as NVMC,
+            KMU_NS as KMU,
-        P0_NS as P0,
+            NVMC_NS as NVMC,
-        PDM_NS as PDM,
+            P0_NS as P0,
-        POWER_NS as POWER,
+            PDM_NS as PDM,
-        PWM0_NS as PWM0,
+            POWER_NS as POWER,
-        PWM1_NS as PWM1,
+            PWM0_NS as PWM0,
-        PWM2_NS as PWM2,
+            PWM1_NS as PWM1,
-        PWM3_NS as PWM3,
+            PWM2_NS as PWM2,
-        REGULATORS_NS as REGULATORS,
+            PWM3_NS as PWM3,
-        RTC0_NS as RTC0,
+            REGULATORS_NS as REGULATORS,
-        RTC1_NS as RTC1,
+            RTC0_NS as RTC0,
-        SAADC_NS as SAADC,
+            RTC1_NS as RTC1,
-        SPIM0_NS as SPIM0,
+            SAADC_NS as SAADC,
-        SPIM1_NS as SPIM1,
+            SPIM0_NS as SPIM0,
-        SPIM2_NS as SPIM2,
+            SPIM1_NS as SPIM1,
-        SPIM3_NS as SPIM3,
+            SPIM2_NS as SPIM2,
-        SPIS0_NS as SPIS0,
+            SPIM3_NS as SPIM3,
-        SPIS1_NS as SPIS1,
+            SPIS0_NS as SPIS0,
-        SPIS2_NS as SPIS2,
+            SPIS1_NS as SPIS1,
-        SPIS3_NS as SPIS3,
+            SPIS2_NS as SPIS2,
-        TIMER0_NS as TIMER0,
+            SPIS3_NS as SPIS3,
-        TIMER1_NS as TIMER1,
+            TIMER0_NS as TIMER0,
-        TIMER2_NS as TIMER2,
+            TIMER1_NS as TIMER1,
-        TWIM0_NS as TWIM0,
+            TIMER2_NS as TIMER2,
-        TWIM1_NS as TWIM1,
+            TWIM0_NS as TWIM0,
-        TWIM2_NS as TWIM2,
+            TWIM1_NS as TWIM1,
-        TWIM3_NS as TWIM3,
+            TWIM2_NS as TWIM2,
-        TWIS0_NS as TWIS0,
+            TWIM3_NS as TWIM3,
-        TWIS1_NS as TWIS1,
+            TWIS0_NS as TWIS0,
-        TWIS2_NS as TWIS2,
+            TWIS1_NS as TWIS1,
-        TWIS3_NS as TWIS3,
+            TWIS2_NS as TWIS2,
-        UARTE0_NS as UARTE0,
+            TWIS3_NS as TWIS3,
-        UARTE1_NS as UARTE1,
+            UARTE0_NS as UARTE0,
-        UARTE2_NS as UARTE2,
+            UARTE1_NS as UARTE1,
-        UARTE3_NS as UARTE3,
+            UARTE2_NS as UARTE2,
-        VMC_NS as VMC,
+            UARTE3_NS as UARTE3,
-        WDT_NS as WDT,
+            VMC_NS as VMC,
-    };
+            WDT_NS as WDT,
+        };
+    }
 
-    #[cfg(feature = "nrf9160-s")]
+    /// Secure mode (S) peripherals
-    #[doc(no_inline)]
+    pub mod s {
-    pub use nrf9160_pac::{
+        #[doc(no_inline)]
-        CC_HOST_RGF_S as CC_HOST_RGF,
+        pub use nrf9160_pac::{
-        CLOCK_S as CLOCK,
+            CC_HOST_RGF_S as CC_HOST_RGF,
-        CRYPTOCELL_S as CRYPTOCELL,
+            CLOCK_S as CLOCK,
-        CTRL_AP_PERI_S as CTRL_AP_PERI,
+            CRYPTOCELL_S as CRYPTOCELL,
-        DPPIC_S as DPPIC,
+            CTRL_AP_PERI_S as CTRL_AP_PERI,
-        EGU0_S as EGU0,
+            DPPIC_S as DPPIC,
-        EGU1_S as EGU1,
+            EGU0_S as EGU0,
-        EGU2_S as EGU2,
+            EGU1_S as EGU1,
-        EGU3_S as EGU3,
+            EGU2_S as EGU2,
-        EGU4_S as EGU4,
+            EGU3_S as EGU3,
-        EGU5_S as EGU5,
+            EGU4_S as EGU4,
-        FICR_S as FICR,
+            EGU5_S as EGU5,
-        FPU_S as FPU,
+            FICR_S as FICR,
-        GPIOTE0_S as GPIOTE0,
+            FPU_S as FPU,
-        I2S_S as I2S,
+            GPIOTE0_S as GPIOTE0,
-        IPC_S as IPC,
+            I2S_S as I2S,
-        KMU_S as KMU,
+            IPC_S as IPC,
-        NVMC_S as NVMC,
+            KMU_S as KMU,
-        P0_S as P0,
+            NVMC_S as NVMC,
-        PDM_S as PDM,
+            P0_S as P0,
-        POWER_S as POWER,
+            PDM_S as PDM,
-        PWM0_S as PWM0,
+            POWER_S as POWER,
-        PWM1_S as PWM1,
+            PWM0_S as PWM0,
-        PWM2_S as PWM2,
+            PWM1_S as PWM1,
-        PWM3_S as PWM3,
+            PWM2_S as PWM2,
-        REGULATORS_S as REGULATORS,
+            PWM3_S as PWM3,
-        RTC0_S as RTC0,
+            REGULATORS_S as REGULATORS,
-        RTC1_S as RTC1,
+            RTC0_S as RTC0,
-        SAADC_S as SAADC,
+            RTC1_S as RTC1,
-        SPIM0_S as SPIM0,
+            SAADC_S as SAADC,
-        SPIM1_S as SPIM1,
+            SPIM0_S as SPIM0,
-        SPIM2_S as SPIM2,
+            SPIM1_S as SPIM1,
-        SPIM3_S as SPIM3,
+            SPIM2_S as SPIM2,
-        SPIS0_S as SPIS0,
+            SPIM3_S as SPIM3,
-        SPIS1_S as SPIS1,
+            SPIS0_S as SPIS0,
-        SPIS2_S as SPIS2,
+            SPIS1_S as SPIS1,
-        SPIS3_S as SPIS3,
+            SPIS2_S as SPIS2,
-        SPU_S as SPU,
+            SPIS3_S as SPIS3,
-        TAD_S as TAD,
+            SPU_S as SPU,
-        TIMER0_S as TIMER0,
+            TAD_S as TAD,
-        TIMER1_S as TIMER1,
+            TIMER0_S as TIMER0,
-        TIMER2_S as TIMER2,
+            TIMER1_S as TIMER1,
-        TWIM0_S as TWIM0,
+            TIMER2_S as TIMER2,
-        TWIM1_S as TWIM1,
+            TWIM0_S as TWIM0,
-        TWIM2_S as TWIM2,
+            TWIM1_S as TWIM1,
-        TWIM3_S as TWIM3,
+            TWIM2_S as TWIM2,
-        TWIS0_S as TWIS0,
+            TWIM3_S as TWIM3,
-        TWIS1_S as TWIS1,
+            TWIS0_S as TWIS0,
-        TWIS2_S as TWIS2,
+            TWIS1_S as TWIS1,
-        TWIS3_S as TWIS3,
+            TWIS2_S as TWIS2,
-        UARTE0_S as UARTE0,
+            TWIS3_S as TWIS3,
-        UARTE1_S as UARTE1,
+            UARTE0_S as UARTE0,
-        UARTE2_S as UARTE2,
+            UARTE1_S as UARTE1,
-        UARTE3_S as UARTE3,
+            UARTE2_S as UARTE2,
-        UICR_S as UICR,
+            UARTE3_S as UARTE3,
-        VMC_S as VMC,
+            UICR_S as UICR,
-        WDT_S as WDT,
+            VMC_S as VMC,
-    };
+            WDT_S as WDT,
+        };
+    }
+
+    #[cfg(feature = "_ns")]
+    pub use ns::*;
+    #[cfg(feature = "_s")]
+    pub use s::*;
 }
 
 /// The maximum buffer size that the EasyDMA can send/recv in one operation.

embassy-rp/Cargo.toml

@@ -60,7 +60,7 @@ unstable-traits = ["embedded-hal-1", "embedded-hal-nb"]
 
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../embassy-sync" }
-embassy-time = { version = "0.1.4", path = "../embassy-time", features = [ "tick-hz-1_000_000" ] }
+embassy-time = { version = "0.1.5", path = "../embassy-time", features = [ "tick-hz-1_000_000" ] }
 embassy-futures = { version = "0.1.0", path = "../embassy-futures" }
 embassy-hal-internal = {version = "0.1.0", path = "../embassy-hal-internal", features = ["cortex-m", "prio-bits-2"] }
 embassy-embedded-hal = {version = "0.1.0", path = "../embassy-embedded-hal" }

embassy-rp/src/uart/buffered.rs

@@ -5,7 +5,7 @@ use core::task::Poll;
 use atomic_polyfill::{AtomicU8, Ordering};
 use embassy_hal_internal::atomic_ring_buffer::RingBuffer;
 use embassy_sync::waitqueue::AtomicWaker;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 
 use super::*;
 use crate::clocks::clk_peri_freq;
@@ -435,7 +435,7 @@ impl<'d, T: Instance> BufferedUartTx<'d, T> {
         Self::flush().await.unwrap();
         while self.busy() {}
         regs.uartlcr_h().write_set(|w| w.set_brk(true));
-        Timer::after(Duration::from_micros(wait_usecs)).await;
+        Timer::after_micros(wait_usecs).await;
         regs.uartlcr_h().write_clear(|w| w.set_brk(true));
     }
 }

embassy-rp/src/uart/mod.rs

@@ -6,7 +6,7 @@ use atomic_polyfill::{AtomicU16, Ordering};
 use embassy_futures::select::{select, Either};
 use embassy_hal_internal::{into_ref, PeripheralRef};
 use embassy_sync::waitqueue::AtomicWaker;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use pac::uart::regs::Uartris;
 
 use crate::clocks::clk_peri_freq;
@@ -187,7 +187,7 @@ impl<'d, T: Instance, M: Mode> UartTx<'d, T, M> {
         self.blocking_flush().unwrap();
         while self.busy() {}
         regs.uartlcr_h().write_set(|w| w.set_brk(true));
-        Timer::after(Duration::from_micros(wait_usecs)).await;
+        Timer::after_micros(wait_usecs).await;
         regs.uartlcr_h().write_clear(|w| w.set_brk(true));
     }
 }

embassy-stm32-wpan/Cargo.toml

@@ -13,7 +13,7 @@ features = ["stm32wb55rg"]
 [dependencies]
 embassy-stm32 = { version = "0.1.0", path = "../embassy-stm32" }
 embassy-sync = { version = "0.3.0", path = "../embassy-sync" }
-embassy-time = { version = "0.1.4", path = "../embassy-time", optional = true }
+embassy-time = { version = "0.1.5", path = "../embassy-time", optional = true }
 embassy-futures = { version = "0.1.0", path = "../embassy-futures" }
 embassy-hal-internal = { version = "0.1.0", path = "../embassy-hal-internal" }
 embassy-embedded-hal = { version = "0.1.0", path = "../embassy-embedded-hal" }

embassy-stm32/Cargo.toml

@@ -33,7 +33,7 @@ flavors = [
 
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../embassy-sync" }
-embassy-time = { version = "0.1.4", path = "../embassy-time", optional = true }
+embassy-time = { version = "0.1.5", path = "../embassy-time", optional = true }
 embassy-futures = { version = "0.1.0", path = "../embassy-futures" }
 embassy-hal-internal = {version = "0.1.0", path = "../embassy-hal-internal", features = ["cortex-m", "prio-bits-4"] }
 embassy-embedded-hal = {version = "0.1.0", path = "../embassy-embedded-hal" }
@@ -58,7 +58,7 @@ rand_core = "0.6.3"
 sdio-host = "0.5.0"
 embedded-sdmmc = { git = "https://github.com/embassy-rs/embedded-sdmmc-rs", rev = "a4f293d3a6f72158385f79c98634cb8a14d0d2fc", optional = true }
 critical-section = "1.1"
-stm32-metapac = { git = "https://github.com/embassy-rs/stm32-data-generated", tag = "stm32-data-6bfa5a0dcec6a9bd42cea94ba11eeae1a17a7f2c" }
+stm32-metapac = { git = "https://github.com/embassy-rs/stm32-data-generated", tag = "stm32-data-9330e31117668350a62572fdcd2598ec17d08042" }
 vcell = "0.1.3"
 bxcan = "0.7.0"
 nb = "1.0.0"
@@ -76,7 +76,7 @@ critical-section = { version = "1.1", features = ["std"] }
 [build-dependencies]
 proc-macro2 = "1.0.36"
 quote = "1.0.15"
-stm32-metapac = { git = "https://github.com/embassy-rs/stm32-data-generated", tag = "stm32-data-6bfa5a0dcec6a9bd42cea94ba11eeae1a17a7f2c", default-features = false, features = ["metadata"]}
+stm32-metapac = { git = "https://github.com/embassy-rs/stm32-data-generated", tag = "stm32-data-9330e31117668350a62572fdcd2598ec17d08042", default-features = false, features = ["metadata"]}
 
 
 [features]

embassy-stm32/build.rs

@@ -5,7 +5,7 @@ use std::{env, fs};
 
 use proc_macro2::{Ident, TokenStream};
 use quote::{format_ident, quote};
-use stm32_metapac::metadata::ir::{BlockItemInner, Enum};
+use stm32_metapac::metadata::ir::{BlockItemInner, Enum, FieldSet};
 use stm32_metapac::metadata::{MemoryRegionKind, PeripheralRccRegister, METADATA};
 
 fn main() {
@@ -388,41 +388,37 @@ fn main() {
         });
     }
 
+    // ========
+    // Extract the rcc registers
+    let rcc_registers = METADATA
+        .peripherals
+        .iter()
+        .filter_map(|p| p.registers.as_ref())
+        .find(|r| r.kind == "rcc")
+        .unwrap();
+
     // ========
     // Generate rcc fieldset and enum maps
     let rcc_enum_map: HashMap<&str, HashMap<&str, &Enum>> = {
-        let rcc_registers = METADATA
+        let rcc_blocks = rcc_registers.ir.blocks.iter().find(|b| b.name == "Rcc").unwrap().items;
-            .peripherals
+        let rcc_fieldsets: HashMap<&str, &FieldSet> = rcc_registers.ir.fieldsets.iter().map(|f| (f.name, f)).collect();
-            .iter()
+        let rcc_enums: HashMap<&str, &Enum> = rcc_registers.ir.enums.iter().map(|e| (e.name, e)).collect();
-            .filter_map(|p| p.registers.as_ref())
-            .find(|r| r.kind == "rcc")
-            .unwrap()
-            .ir;
 
-        let rcc_blocks = rcc_registers.blocks.iter().find(|b| b.name == "Rcc").unwrap().items;
+        rcc_blocks
-
-        let rcc_block_item_map: HashMap<&str, &str> = rcc_blocks
             .iter()
             .filter_map(|b| match &b.inner {
-                BlockItemInner::Register(register) => register.fieldset.map(|f| (f, b.name)),
+                BlockItemInner::Register(register) => register.fieldset.map(|f| (b.name, f)),
                 _ => None,
             })
-            .collect();
+            .filter_map(|(b, f)| {
-
+                rcc_fieldsets.get(f).map(|f| {
-        let rcc_enum_map: HashMap<&str, &Enum> = rcc_registers.enums.iter().map(|e| (e.name, e)).collect();
-
-        rcc_registers
-            .fieldsets
-            .iter()
-            .filter_map(|f| {
-                rcc_block_item_map.get(f.name).map(|b| {
                     (
-                        *b,
+                        b,
                         f.fields
                             .iter()
                             .filter_map(|f| {
                                 let enumm = f.enumm?;
-                                let enumm = rcc_enum_map.get(enumm)?;
+                                let enumm = rcc_enums.get(enumm)?;
 
                                 Some((f.name, *enumm))
                             })
@@ -470,7 +466,13 @@ fn main() {
 
             let ptype = if let Some(reg) = &p.registers { reg.kind } else { "" };
             let pname = format_ident!("{}", p.name);
-            let clk = format_ident!("{}", rcc.clock.to_ascii_lowercase());
+            let clk = format_ident!(
+                "{}",
+                rcc.clock
+                    .to_ascii_lowercase()
+                    .replace("ahb", "hclk")
+                    .replace("apb", "pclk")
+            );
             let en_reg = format_ident!("{}", en.register.to_ascii_lowercase());
             let set_en_field = format_ident!("set_{}", en.field.to_ascii_lowercase());
 
@@ -499,8 +501,10 @@ fn main() {
             };
 
             let mux_for = |mux: Option<&'static PeripheralRccRegister>| {
-                // temporary hack to restrict the scope of the implementation to h5
+                let checked_rccs = HashSet::from(["h5", "h50", "h7", "h7ab", "h7rm0433", "g4"]);
-                if !&chip_name.starts_with("stm32h5") {
+
+                // restrict mux implementation to supported versions
+                if !checked_rccs.contains(rcc_registers.version) {
                     return None;
                 }
 
@@ -523,12 +527,16 @@ fn main() {
                         .filter(|v| v.name != "DISABLE")
                         .map(|v| {
                             let variant_name = format_ident!("{}", v.name);
+                            let clock_name = format_ident!("{}", v.name.to_ascii_lowercase());
 
-                            // temporary hack to restrict the scope of the implementation until clock names can be stabilized
+                            if v.name.starts_with("HCLK") || v.name.starts_with("PCLK") || v.name == "SYS" { 
-                            let clock_name = format_ident!("mux_{}", v.name.to_ascii_lowercase());
+                                quote! {
-
+                                    #enum_name::#variant_name => unsafe { crate::rcc::get_freqs().#clock_name },
-                            quote! {
+                                }
-                                #enum_name::#variant_name => unsafe { crate::rcc::get_freqs().#clock_name.unwrap() },
+                            } else {
+                                quote! {
+                                    #enum_name::#variant_name => unsafe { crate::rcc::get_freqs().#clock_name.unwrap() },
+                                }
                             }
                         })
                         .collect();
@@ -1012,15 +1020,7 @@ fn main() {
 
     // ========
     // Generate Div/Mul impls for RCC prescalers/dividers/multipliers.
-    let rcc_registers = METADATA
+    for e in rcc_registers.ir.enums {
-        .peripherals
-        .iter()
-        .filter_map(|p| p.registers.as_ref())
-        .find(|r| r.kind == "rcc")
-        .unwrap()
-        .ir;
-
-    for e in rcc_registers.enums {
         fn is_rcc_name(e: &str) -> bool {
             match e {
                 "Pllp" | "Pllq" | "Pllr" | "Pllm" | "Plln" => true,

embassy-stm32/src/dac/mod.rs

@@ -564,7 +564,7 @@ foreach_peripheral!(
                 #[cfg(any(rcc_h7, rcc_h7rm0433))]
                 impl crate::rcc::sealed::RccPeripheral for peripherals::$inst {
                     fn frequency() -> crate::time::Hertz {
-                        critical_section::with(|_| unsafe { crate::rcc::get_freqs().apb1 })
+                        critical_section::with(|_| unsafe { crate::rcc::get_freqs().pclk1 })
                     }
 
                     fn enable_and_reset_with_cs(_cs: critical_section::CriticalSection) {

embassy-stm32/src/eth/v1/mod.rs

@@ -191,7 +191,7 @@ impl<'d, T: Instance, P: PHY> Ethernet<'d, T, P> {
         // TODO MTU size setting not found for v1 ethernet, check if correct
 
         // NOTE(unsafe) We got the peripheral singleton, which means that `rcc::init` was called
-        let hclk = unsafe { crate::rcc::get_freqs() }.ahb1;
+        let hclk = unsafe { crate::rcc::get_freqs() }.hclk1;
         let hclk_mhz = hclk.0 / 1_000_000;
 
         // Set the MDC clock frequency in the range 1MHz - 2.5MHz

embassy-stm32/src/eth/v2/mod.rs

@@ -164,7 +164,7 @@ impl<'d, T: Instance, P: PHY> Ethernet<'d, T, P> {
         });
 
         // NOTE(unsafe) We got the peripheral singleton, which means that `rcc::init` was called
-        let hclk = unsafe { crate::rcc::get_freqs() }.ahb1;
+        let hclk = unsafe { crate::rcc::get_freqs() }.hclk1;
         let hclk_mhz = hclk.0 / 1_000_000;
 
         // Set the MDC clock frequency in the range 1MHz - 2.5MHz

embassy-stm32/src/i2s.rs

@@ -170,7 +170,7 @@ impl<'d, T: Instance, Tx, Rx> I2S<'d, T, Tx, Rx> {
         let spi = Spi::new_internal(peri, txdma, rxdma, spi_cfg);
 
         #[cfg(all(rcc_f4, not(stm32f410)))]
-        let pclk = unsafe { get_freqs() }.plli2s.unwrap();
+        let pclk = unsafe { get_freqs() }.plli2s1_q.unwrap();
 
         #[cfg(stm32f410)]
         let pclk = T::frequency();

embassy-stm32/src/rcc/bd.rs

@@ -106,7 +106,7 @@ impl LsConfig {
 
     pub const fn off() -> Self {
         Self {
-            rtc: RtcClockSource::NOCLOCK,
+            rtc: RtcClockSource::DISABLE,
             lsi: false,
             lse: None,
         }
@@ -133,7 +133,7 @@ impl LsConfig {
                 Some(LSI_FREQ)
             }
             RtcClockSource::LSE => Some(self.lse.as_ref().unwrap().frequency),
-            RtcClockSource::NOCLOCK => None,
+            RtcClockSource::DISABLE => None,
             _ => todo!(),
         };
 
@@ -180,7 +180,7 @@ impl LsConfig {
         ok &= reg.rtcsel() == self.rtc;
         #[cfg(not(rcc_wba))]
         {
-            ok &= reg.rtcen() == (self.rtc != RtcClockSource::NOCLOCK);
+            ok &= reg.rtcen() == (self.rtc != RtcClockSource::DISABLE);
         }
         ok &= reg.lseon() == lse_en;
         ok &= reg.lsebyp() == lse_byp;
@@ -225,7 +225,7 @@ impl LsConfig {
             while !bdcr().read().lserdy() {}
         }
 
-        if self.rtc != RtcClockSource::NOCLOCK {
+        if self.rtc != RtcClockSource::DISABLE {
             bdcr().modify(|w| {
                 #[cfg(any(rtc_v2h7, rtc_v2l4, rtc_v2wb, rtc_v3, rtc_v3u5))]
                 assert!(!w.lsecsson(), "RTC is not compatible with LSE CSS, yet.");

embassy-stm32/src/rcc/c0.rs

@@ -135,9 +135,9 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        apb1: apb_freq,
+        pclk1: apb_freq,
-        apb1_tim: apb_tim_freq,
+        pclk1_tim: apb_tim_freq,
         rtc,
     });
 }

embassy-stm32/src/rcc/f0.rs

@@ -162,11 +162,11 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: Hertz(real_sysclk),
-        apb1: Hertz(pclk),
+        pclk1: Hertz(pclk),
-        apb2: Hertz(pclk),
+        pclk2: Hertz(pclk),
-        apb1_tim: Hertz(pclk * timer_mul),
+        pclk1_tim: Hertz(pclk * timer_mul),
-        apb2_tim: Hertz(pclk * timer_mul),
+        pclk2_tim: Hertz(pclk * timer_mul),
-        ahb1: Hertz(hclk),
+        hclk1: Hertz(hclk),
         rtc,
     });
 }

embassy-stm32/src/rcc/f1.rs

@@ -180,11 +180,11 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: Hertz(real_sysclk),
-        apb1: Hertz(pclk1),
+        pclk1: Hertz(pclk1),
-        apb2: Hertz(pclk2),
+        pclk2: Hertz(pclk2),
-        apb1_tim: Hertz(pclk1 * timer_mul1),
+        pclk1_tim: Hertz(pclk1 * timer_mul1),
-        apb2_tim: Hertz(pclk2 * timer_mul2),
+        pclk2_tim: Hertz(pclk2 * timer_mul2),
-        ahb1: Hertz(hclk),
+        hclk1: Hertz(hclk),
         adc: Some(Hertz(adcclk)),
         rtc,
     });

embassy-stm32/src/rcc/f2.rs

@@ -307,14 +307,14 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        ahb2: ahb_freq,
+        hclk2: ahb_freq,
-        ahb3: ahb_freq,
+        hclk3: ahb_freq,
-        apb1: apb1_freq,
+        pclk1: apb1_freq,
-        apb1_tim: apb1_tim_freq,
+        pclk1_tim: apb1_tim_freq,
-        apb2: apb2_freq,
+        pclk2: apb2_freq,
-        apb2_tim: apb2_tim_freq,
+        pclk2_tim: apb2_tim_freq,
-        pll48: Some(pll_clocks.pll48_freq),
+        pll1_q: Some(pll_clocks.pll48_freq),
         rtc,
     });
 }

embassy-stm32/src/rcc/f3.rs

@@ -281,11 +281,11 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sysclk,
-        apb1: pclk1,
+        pclk1: pclk1,
-        apb2: pclk2,
+        pclk2: pclk2,
-        apb1_tim: pclk1 * timer_mul1,
+        pclk1_tim: pclk1 * timer_mul1,
-        apb2_tim: pclk2 * timer_mul2,
+        pclk2_tim: pclk2 * timer_mul2,
-        ahb1: hclk,
+        hclk1: hclk,
         #[cfg(rcc_f3)]
         adc: adc,
         #[cfg(all(rcc_f3, adc3_common))]

embassy-stm32/src/rcc/f4.rs

@@ -340,23 +340,27 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: Hertz(sysclk),
-        apb1: Hertz(pclk1),
+        pclk1: Hertz(pclk1),
-        apb2: Hertz(pclk2),
+        pclk2: Hertz(pclk2),
 
-        apb1_tim: Hertz(pclk1 * timer_mul1),
+        pclk1_tim: Hertz(pclk1 * timer_mul1),
-        apb2_tim: Hertz(pclk2 * timer_mul2),
+        pclk2_tim: Hertz(pclk2 * timer_mul2),
 
-        ahb1: Hertz(hclk),
+        hclk1: Hertz(hclk),
-        ahb2: Hertz(hclk),
+        hclk2: Hertz(hclk),
-        ahb3: Hertz(hclk),
+        hclk3: Hertz(hclk),
 
-        pll48: plls.pll48clk.map(Hertz),
+        pll1_q: plls.pll48clk.map(Hertz),
 
         #[cfg(not(stm32f410))]
-        plli2s: plls.plli2sclk.map(Hertz),
+        plli2s1_q: plls.plli2sclk.map(Hertz),
+        #[cfg(not(stm32f410))]
+        plli2s1_r: None,
 
         #[cfg(any(stm32f427, stm32f429, stm32f437, stm32f439, stm32f446, stm32f469, stm32f479))]
-        pllsai: plls.pllsaiclk.map(Hertz),
+        pllsai1_q: plls.pllsaiclk.map(Hertz),
+        #[cfg(any(stm32f427, stm32f429, stm32f437, stm32f439, stm32f446, stm32f469, stm32f479))]
+        pllsai1_r: None,
 
         rtc,
     });

embassy-stm32/src/rcc/f7.rs

@@ -259,17 +259,17 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: Hertz(sysclk),
-        apb1: Hertz(pclk1),
+        pclk1: Hertz(pclk1),
-        apb2: Hertz(pclk2),
+        pclk2: Hertz(pclk2),
 
-        apb1_tim: Hertz(pclk1 * timer_mul1),
+        pclk1_tim: Hertz(pclk1 * timer_mul1),
-        apb2_tim: Hertz(pclk2 * timer_mul2),
+        pclk2_tim: Hertz(pclk2 * timer_mul2),
 
-        ahb1: Hertz(hclk),
+        hclk1: Hertz(hclk),
-        ahb2: Hertz(hclk),
+        hclk2: Hertz(hclk),
-        ahb3: Hertz(hclk),
+        hclk3: Hertz(hclk),
 
-        pll48: plls.pll48clk.map(Hertz),
+        pll1_q: plls.pll48clk.map(Hertz),
 
         rtc,
     });

embassy-stm32/src/rcc/g0.rs

@@ -89,7 +89,7 @@ impl Default for Config {
 impl PllConfig {
     pub(crate) fn init(self) -> Hertz {
         let (src, input_freq) = match self.source {
-            PllSrc::HSI16 => (vals::Pllsrc::HSI16, HSI_FREQ),
+            PllSrc::HSI16 => (vals::Pllsrc::HSI, HSI_FREQ),
             PllSrc::HSE(freq) => (vals::Pllsrc::HSE, freq),
         };
 
@@ -186,7 +186,7 @@ pub(crate) unsafe fn init(config: Config) {
         }
         ClockSrc::PLL(pll) => {
             let freq = pll.init();
-            (freq, Sw::PLLRCLK)
+            (freq, Sw::PLL1_R)
         }
         ClockSrc::LSI => {
             // Enable LSI
@@ -275,9 +275,9 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        apb1: apb_freq,
+        pclk1: apb_freq,
-        apb1_tim: apb_tim_freq,
+        pclk1_tim: apb_tim_freq,
         rtc,
     });
 }

embassy-stm32/src/rcc/g4.rs

@@ -33,7 +33,7 @@ impl Into<Pllsrc> for PllSrc {
     fn into(self) -> Pllsrc {
         match self {
             PllSrc::HSE(..) => Pllsrc::HSE,
-            PllSrc::HSI16 => Pllsrc::HSI16,
+            PllSrc::HSI16 => Pllsrc::HSI,
         }
     }
 }
@@ -118,9 +118,9 @@ impl Default for Config {
             apb2_pre: APBPrescaler::DIV1,
             low_power_run: false,
             pll: None,
-            clock_48mhz_src: None,
+            clock_48mhz_src: Some(Clock48MhzSrc::Hsi48(None)),
-            adc12_clock_source: Adcsel::NOCLK,
+            adc12_clock_source: Adcsel::DISABLE,
-            adc345_clock_source: Adcsel::NOCLK,
+            adc345_clock_source: Adcsel::DISABLE,
             ls: Default::default(),
         }
     }
@@ -201,7 +201,7 @@ pub(crate) unsafe fn init(config: Config) {
             RCC.cr().write(|w| w.set_hsion(true));
             while !RCC.cr().read().hsirdy() {}
 
-            (HSI_FREQ, Sw::HSI16)
+            (HSI_FREQ, Sw::HSI)
         }
         ClockSrc::HSE(freq) => {
             // Enable HSE
@@ -249,7 +249,7 @@ pub(crate) unsafe fn init(config: Config) {
                 }
             }
 
-            (Hertz(freq), Sw::PLLRCLK)
+            (Hertz(freq), Sw::PLL1_R)
         }
     };
 
@@ -286,7 +286,7 @@ pub(crate) unsafe fn init(config: Config) {
                 let pllq_freq = pll_freq.as_ref().and_then(|f| f.pll_q);
                 assert!(pllq_freq.is_some() && pllq_freq.unwrap().0 == 48_000_000);
 
-                crate::pac::rcc::vals::Clk48sel::PLLQCLK
+                crate::pac::rcc::vals::Clk48sel::PLL1_Q
             }
             Clock48MhzSrc::Hsi48(crs_config) => {
                 // Enable HSI48
@@ -326,16 +326,16 @@ pub(crate) unsafe fn init(config: Config) {
     RCC.ccipr().modify(|w| w.set_adc345sel(config.adc345_clock_source));
 
     let adc12_ck = match config.adc12_clock_source {
-        AdcClockSource::NOCLK => None,
+        AdcClockSource::DISABLE => None,
-        AdcClockSource::PLLP => pll_freq.as_ref().unwrap().pll_p,
+        AdcClockSource::PLL1_P => pll_freq.as_ref().unwrap().pll_p,
-        AdcClockSource::SYSCLK => Some(sys_clk),
+        AdcClockSource::SYS => Some(sys_clk),
         _ => unreachable!(),
     };
 
     let adc345_ck = match config.adc345_clock_source {
-        AdcClockSource::NOCLK => None,
+        AdcClockSource::DISABLE => None,
-        AdcClockSource::PLLP => pll_freq.as_ref().unwrap().pll_p,
+        AdcClockSource::PLL1_P => pll_freq.as_ref().unwrap().pll_p,
-        AdcClockSource::SYSCLK => Some(sys_clk),
+        AdcClockSource::SYS => Some(sys_clk),
         _ => unreachable!(),
     };
 
@@ -348,14 +348,15 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        ahb2: ahb_freq,
+        hclk2: ahb_freq,
-        apb1: apb1_freq,
+        pclk1: apb1_freq,
-        apb1_tim: apb1_tim_freq,
+        pclk1_tim: apb1_tim_freq,
-        apb2: apb2_freq,
+        pclk2: apb2_freq,
-        apb2_tim: apb2_tim_freq,
+        pclk2_tim: apb2_tim_freq,
         adc: adc12_ck,
         adc34: adc345_ck,
+        pll1_p: None,
         rtc,
     });
 }

embassy-stm32/src/rcc/h.rs

@@ -163,10 +163,6 @@ impl From<TimerPrescaler> for Timpre {
 pub struct Config {
     pub hsi: Option<Hsi>,
     pub hse: Option<Hse>,
-    #[cfg(stm32h7)]
-    pub lse: Option<Lse>,
-    #[cfg(stm32h7)]
-    pub lsi: bool,
     pub csi: bool,
     pub hsi48: bool,
     pub sys: Sysclk,
@@ -199,10 +195,6 @@ impl Default for Config {
         Self {
             hsi: Some(Hsi::Mhz64),
             hse: None,
-            #[cfg(stm32h7)]
-            lse: None,
-            #[cfg(stm32h7)]
-            lsi: false,
             csi: false,
             hsi48: false,
             sys: Sysclk::HSI,
@@ -395,7 +387,7 @@ pub(crate) unsafe fn init(config: Config) {
         Sysclk::HSI => (unwrap!(hsi), Sw::HSI),
         Sysclk::HSE => (unwrap!(hse), Sw::HSE),
         Sysclk::CSI => (unwrap!(csi), Sw::CSI),
-        Sysclk::Pll1P => (unwrap!(pll1.p), Sw::PLL1),
+        Sysclk::Pll1P => (unwrap!(pll1.p), Sw::PLL1_P),
     };
 
     // Check limits.
@@ -453,12 +445,12 @@ pub(crate) unsafe fn init(config: Config) {
     };
     #[cfg(stm32h5)]
     let adc = match config.adc_clock_source {
-        AdcClockSource::HCLK => Some(hclk),
+        AdcClockSource::HCLK1 => Some(hclk),
-        AdcClockSource::SYSCLK => Some(sys),
+        AdcClockSource::SYS => Some(sys),
         AdcClockSource::PLL2_R => pll2.r,
         AdcClockSource::HSE => hse,
-        AdcClockSource::HSI_KER => hsi,
+        AdcClockSource::HSI => hsi,
-        AdcClockSource::CSI_KER => csi,
+        AdcClockSource::CSI => csi,
         _ => unreachable!(),
     };
 
@@ -532,66 +524,65 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys,
-        ahb1: hclk,
+        hclk1: hclk,
-        ahb2: hclk,
+        hclk2: hclk,
-        ahb3: hclk,
+        hclk3: hclk,
-        ahb4: hclk,
+        hclk4: hclk,
-        apb1,
+        pclk1: apb1,
-        apb2,
+        pclk2: apb2,
-        apb3,
+        pclk3: apb3,
         #[cfg(stm32h7)]
-        apb4,
+        pclk4: apb4,
-        apb1_tim,
+        #[cfg(stm32h5)]
-        apb2_tim,
+        pclk4: Hertz(1),
+        pclk1_tim: apb1_tim,
+        pclk2_tim: apb2_tim,
         adc,
         rtc,
 
+        #[cfg(any(stm32h5, stm32h7))]
+        hsi: None,
         #[cfg(stm32h5)]
-        mux_rcc_pclk1: Some(apb1),
+        hsi48: None,
         #[cfg(stm32h5)]
-        mux_pll2_q: None,
+        lsi: None,
-        #[cfg(stm32h5)]
+        #[cfg(any(stm32h5, stm32h7))]
-        mux_pll3_q: None,
+        csi: None,
-        #[cfg(stm32h5)]
-        mux_hsi_ker: None,
-        #[cfg(stm32h5)]
-        mux_csi_ker: None,
-        #[cfg(stm32h5)]
-        mux_lse: None,
-        #[cfg(stm32h5)]
-        mux_pll1_q: pll1.q,
-        #[cfg(stm32h5)]
-        mux_pll2_p: pll2.p,
-        #[cfg(rcc_h5)]
-        mux_pll3_p: pll3.p,
-        #[cfg(stm32h5)]
-        mux_audioclk: None,
-        #[cfg(stm32h5)]
-        mux_per: None,
 
-        #[cfg(rcc_h5)]
+        #[cfg(any(stm32h5, stm32h7))]
-        mux_pll3_r: pll3.r,
+        lse: None,
-        #[cfg(all(not(rcc_h5), stm32h5))]
+        #[cfg(any(stm32h5, stm32h7))]
-        mux_pll3_r: None,
+        hse: None,
-        #[cfg(stm32h5)]
+
-        mux_rcc_pclk3: Some(apb3),
+        #[cfg(any(stm32h5, stm32h7))]
-        #[cfg(stm32h5)]
+        pll1_q: pll1.q,
-        mux_pll3_1: None,
+        #[cfg(any(stm32h5, stm32h7))]
-        #[cfg(stm32h5)]
+        pll2_p: pll2.p,
-        mux_hsi48_ker: None,
+        #[cfg(any(stm32h5, stm32h7))]
-        #[cfg(stm32h5)]
+        pll2_q: pll2.q,
-        mux_lsi_ker: None,
+        #[cfg(any(stm32h5, stm32h7))]
-        #[cfg(stm32h5)]
+        pll2_r: pll2.r,
-        mux_pll2_r: pll2.r,
+        #[cfg(any(rcc_h5, stm32h7))]
-        #[cfg(stm32h5)]
+        pll3_p: pll3.p,
-        mux_rcc_pclk2: Some(apb2),
+        #[cfg(any(rcc_h5, stm32h7))]
-        #[cfg(stm32h5)]
+        pll3_q: pll3.q,
-        mux_rcc_pclk4: None,
+        #[cfg(any(rcc_h5, stm32h7))]
-        #[cfg(stm32h5)]
+        pll3_r: pll3.r,
-        mux_hse: hse,
+
+        #[cfg(rcc_h50)]
+        pll3_p: None,
+        #[cfg(rcc_h50)]
+        pll3_q: None,
+        #[cfg(rcc_h50)]
+        pll3_r: None,
 
         #[cfg(stm32h5)]
-        mux_hsi48: None,
+        audioclk: None,
+        #[cfg(any(stm32h5, stm32h7))]
+        per: None,
+
+        #[cfg(stm32h7)]
+        rcc_pclk_d3: None,
     });
 }
 

embassy-stm32/src/rcc/l0l1.rs

@@ -209,11 +209,11 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        apb1: apb1_freq,
+        pclk1: apb1_freq,
-        apb2: apb2_freq,
+        pclk2: apb2_freq,
-        apb1_tim: apb1_tim_freq,
+        pclk1_tim: apb1_tim_freq,
-        apb2_tim: apb2_tim_freq,
+        pclk2_tim: apb2_tim_freq,
         rtc,
     });
 }

embassy-stm32/src/rcc/l4.rs

@@ -1,296 +0,0 @@
-use crate::pac::rcc::regs::Cfgr;
-pub use crate::pac::rcc::vals::{
-    Hpre as AHBPrescaler, Msirange as MSIRange, Pllm as PllPreDiv, Plln as PllMul, Pllp as PllPDiv, Pllq as PllQDiv,
-    Pllr as PllRDiv, Ppre as APBPrescaler,
-};
-use crate::pac::rcc::vals::{Msirange, Pllsrc, Sw};
-use crate::pac::{FLASH, RCC};
-use crate::rcc::{set_freqs, Clocks};
-use crate::time::Hertz;
-
-/// HSI speed
-pub const HSI_FREQ: Hertz = Hertz(16_000_000);
-
-/// System clock mux source
-#[derive(Clone, Copy)]
-pub enum ClockSrc {
-    MSI(MSIRange),
-    PLL(PLLSource, PllRDiv, PllPreDiv, PllMul, Option<PllQDiv>),
-    HSE(Hertz),
-    HSI16,
-}
-
-/// PLL clock input source
-#[derive(Clone, Copy)]
-pub enum PLLSource {
-    HSI16,
-    HSE(Hertz),
-    MSI(MSIRange),
-}
-
-impl From<PLLSource> for Pllsrc {
-    fn from(val: PLLSource) -> Pllsrc {
-        match val {
-            PLLSource::HSI16 => Pllsrc::HSI16,
-            PLLSource::HSE(_) => Pllsrc::HSE,
-            PLLSource::MSI(_) => Pllsrc::MSI,
-        }
-    }
-}
-
-/// Clocks configutation
-pub struct Config {
-    pub mux: ClockSrc,
-    pub ahb_pre: AHBPrescaler,
-    pub apb1_pre: APBPrescaler,
-    pub apb2_pre: APBPrescaler,
-    pub pllsai1: Option<(PllMul, PllPreDiv, Option<PllRDiv>, Option<PllQDiv>, Option<PllPDiv>)>,
-    #[cfg(not(any(stm32l471, stm32l475, stm32l476, stm32l486)))]
-    pub hsi48: bool,
-    pub ls: super::LsConfig,
-}
-
-impl Default for Config {
-    #[inline]
-    fn default() -> Config {
-        Config {
-            mux: ClockSrc::MSI(MSIRange::RANGE4M),
-            ahb_pre: AHBPrescaler::DIV1,
-            apb1_pre: APBPrescaler::DIV1,
-            apb2_pre: APBPrescaler::DIV1,
-            pllsai1: None,
-            #[cfg(not(any(stm32l471, stm32l475, stm32l476, stm32l486)))]
-            hsi48: false,
-            ls: Default::default(),
-        }
-    }
-}
-
-pub(crate) unsafe fn init(config: Config) {
-    // Switch to MSI to prevent problems with PLL configuration.
-    if !RCC.cr().read().msion() {
-        // Turn on MSI and configure it to 4MHz.
-        RCC.cr().modify(|w| {
-            w.set_msirgsel(true); // MSI Range is provided by MSIRANGE[3:0].
-            w.set_msirange(MSIRange::RANGE4M);
-            w.set_msipllen(false);
-            w.set_msion(true)
-        });
-
-        // Wait until MSI is running
-        while !RCC.cr().read().msirdy() {}
-    }
-    if RCC.cfgr().read().sws() != Sw::MSI {
-        // Set MSI as a clock source, reset prescalers.
-        RCC.cfgr().write_value(Cfgr::default());
-        // Wait for clock switch status bits to change.
-        while RCC.cfgr().read().sws() != Sw::MSI {}
-    }
-
-    let rtc = config.ls.init();
-
-    let (sys_clk, sw) = match config.mux {
-        ClockSrc::MSI(range) => {
-            // Enable MSI
-            RCC.cr().write(|w| {
-                w.set_msirange(range);
-                w.set_msirgsel(true);
-                w.set_msion(true);
-
-                // If LSE is enabled, enable calibration of MSI
-                w.set_msipllen(config.ls.lse.is_some());
-            });
-            while !RCC.cr().read().msirdy() {}
-
-            // Enable as clock source for USB, RNG if running at 48 MHz
-            if range == MSIRange::RANGE48M {
-                RCC.ccipr().modify(|w| {
-                    w.set_clk48sel(0b11);
-                });
-            }
-            (msirange_to_hertz(range), Sw::MSI)
-        }
-        ClockSrc::HSI16 => {
-            // Enable HSI16
-            RCC.cr().write(|w| w.set_hsion(true));
-            while !RCC.cr().read().hsirdy() {}
-
-            (HSI_FREQ, Sw::HSI16)
-        }
-        ClockSrc::HSE(freq) => {
-            // Enable HSE
-            RCC.cr().write(|w| w.set_hseon(true));
-            while !RCC.cr().read().hserdy() {}
-
-            (freq, Sw::HSE)
-        }
-        ClockSrc::PLL(src, divr, prediv, mul, divq) => {
-            let src_freq = match src {
-                PLLSource::HSE(freq) => {
-                    // Enable HSE
-                    RCC.cr().write(|w| w.set_hseon(true));
-                    while !RCC.cr().read().hserdy() {}
-                    freq
-                }
-                PLLSource::HSI16 => {
-                    // Enable HSI
-                    RCC.cr().write(|w| w.set_hsion(true));
-                    while !RCC.cr().read().hsirdy() {}
-                    HSI_FREQ
-                }
-                PLLSource::MSI(range) => {
-                    // Enable MSI
-                    RCC.cr().write(|w| {
-                        w.set_msirange(range);
-                        w.set_msipllen(false); // should be turned on if LSE is started
-                        w.set_msirgsel(true);
-                        w.set_msion(true);
-                    });
-                    while !RCC.cr().read().msirdy() {}
-
-                    msirange_to_hertz(range)
-                }
-            };
-
-            // Disable PLL
-            RCC.cr().modify(|w| w.set_pllon(false));
-            while RCC.cr().read().pllrdy() {}
-
-            let freq = src_freq / prediv * mul / divr;
-
-            #[cfg(any(stm32l4px, stm32l4qx, stm32l4rx, stm32l4sx))]
-            assert!(freq.0 <= 120_000_000);
-            #[cfg(not(any(stm32l4px, stm32l4qx, stm32l4rx, stm32l4sx)))]
-            assert!(freq.0 <= 80_000_000);
-
-            RCC.pllcfgr().write(move |w| {
-                w.set_plln(mul);
-                w.set_pllm(prediv);
-                w.set_pllr(divr);
-                if let Some(divq) = divq {
-                    w.set_pllq(divq);
-                    w.set_pllqen(true);
-                }
-                w.set_pllsrc(src.into());
-            });
-
-            // Enable as clock source for USB, RNG if PLL48 divisor is provided
-            if let Some(divq) = divq {
-                let freq = src_freq / prediv * mul / divq;
-                assert!(freq.0 == 48_000_000);
-                RCC.ccipr().modify(|w| {
-                    w.set_clk48sel(0b10);
-                });
-            }
-
-            if let Some((mul, prediv, r_div, q_div, p_div)) = config.pllsai1 {
-                RCC.pllsai1cfgr().write(move |w| {
-                    w.set_plln(mul);
-                    w.set_pllm(prediv);
-                    if let Some(r_div) = r_div {
-                        w.set_pllr(r_div);
-                        w.set_pllren(true);
-                    }
-                    if let Some(q_div) = q_div {
-                        w.set_pllq(q_div);
-                        w.set_pllqen(true);
-                        let freq = src_freq / prediv * mul / q_div;
-                        if freq.0 == 48_000_000 {
-                            RCC.ccipr().modify(|w| {
-                                w.set_clk48sel(0b1);
-                            });
-                        }
-                    }
-                    if let Some(p_div) = p_div {
-                        w.set_pllp(p_div);
-                        w.set_pllpen(true);
-                    }
-                });
-
-                RCC.cr().modify(|w| w.set_pllsai1on(true));
-            }
-
-            // Enable PLL
-            RCC.cr().modify(|w| w.set_pllon(true));
-            while !RCC.cr().read().pllrdy() {}
-            RCC.pllcfgr().modify(|w| w.set_pllren(true));
-
-            (freq, Sw::PLL)
-        }
-    };
-
-    #[cfg(not(any(stm32l471, stm32l475, stm32l476, stm32l486)))]
-    if config.hsi48 {
-        RCC.crrcr().modify(|w| w.set_hsi48on(true));
-        while !RCC.crrcr().read().hsi48rdy() {}
-
-        // Enable as clock source for USB, RNG and SDMMC
-        RCC.ccipr().modify(|w| w.set_clk48sel(0));
-    }
-
-    // Set flash wait states
-    FLASH.acr().modify(|w| {
-        w.set_latency(match sys_clk.0 {
-            0..=16_000_000 => 0,
-            0..=32_000_000 => 1,
-            0..=48_000_000 => 2,
-            0..=64_000_000 => 3,
-            _ => 4,
-        })
-    });
-
-    RCC.cfgr().modify(|w| {
-        w.set_sw(sw);
-        w.set_hpre(config.ahb_pre);
-        w.set_ppre1(config.apb1_pre);
-        w.set_ppre2(config.apb2_pre);
-    });
-
-    let ahb_freq = sys_clk / config.ahb_pre;
-
-    let (apb1_freq, apb1_tim_freq) = match config.apb1_pre {
-        APBPrescaler::DIV1 => (ahb_freq, ahb_freq),
-        pre => {
-            let freq = ahb_freq / pre;
-            (freq, freq * 2u32)
-        }
-    };
-
-    let (apb2_freq, apb2_tim_freq) = match config.apb2_pre {
-        APBPrescaler::DIV1 => (ahb_freq, ahb_freq),
-        pre => {
-            let freq = ahb_freq / pre;
-            (freq, freq * 2u32)
-        }
-    };
-
-    set_freqs(Clocks {
-        sys: sys_clk,
-        ahb1: ahb_freq,
-        ahb2: ahb_freq,
-        ahb3: ahb_freq,
-        apb1: apb1_freq,
-        apb2: apb2_freq,
-        apb1_tim: apb1_tim_freq,
-        apb2_tim: apb2_tim_freq,
-        rtc,
-    });
-}
-
-fn msirange_to_hertz(range: Msirange) -> Hertz {
-    match range {
-        MSIRange::RANGE100K => Hertz(100_000),
-        MSIRange::RANGE200K => Hertz(200_000),
-        MSIRange::RANGE400K => Hertz(400_000),
-        MSIRange::RANGE800K => Hertz(800_000),
-        MSIRange::RANGE1M => Hertz(1_000_000),
-        MSIRange::RANGE2M => Hertz(2_000_000),
-        MSIRange::RANGE4M => Hertz(4_000_000),
-        MSIRange::RANGE8M => Hertz(8_000_000),
-        MSIRange::RANGE16M => Hertz(16_000_000),
-        MSIRange::RANGE24M => Hertz(24_000_000),
-        MSIRange::RANGE32M => Hertz(32_000_000),
-        MSIRange::RANGE48M => Hertz(48_000_000),
-        _ => unreachable!(),
-    }
-}

embassy-stm32/src/rcc/l4l5.rs

@@ -0,0 +1,421 @@
+use crate::pac::rcc::regs::Cfgr;
+use crate::pac::rcc::vals::Msirgsel;
+pub use crate::pac::rcc::vals::{
+    Clk48sel as Clk48Src, Hpre as AHBPrescaler, Msirange as MSIRange, Pllm as PllPreDiv, Plln as PllMul,
+    Pllp as PllPDiv, Pllq as PllQDiv, Pllr as PllRDiv, Pllsrc as PLLSource, Ppre as APBPrescaler, Sw as ClockSrc,
+};
+use crate::pac::{FLASH, RCC};
+use crate::rcc::{set_freqs, Clocks};
+use crate::time::Hertz;
+
+/// HSI speed
+pub const HSI_FREQ: Hertz = Hertz(16_000_000);
+
+#[derive(Clone, Copy)]
+pub struct Pll {
+    /// PLL source
+    pub source: PLLSource,
+
+    /// PLL pre-divider (DIVM).
+    pub prediv: PllPreDiv,
+
+    /// PLL multiplication factor.
+    pub mul: PllMul,
+
+    /// PLL P division factor. If None, PLL P output is disabled.
+    pub divp: Option<PllPDiv>,
+    /// PLL Q division factor. If None, PLL Q output is disabled.
+    pub divq: Option<PllQDiv>,
+    /// PLL R division factor. If None, PLL R output is disabled.
+    pub divr: Option<PllRDiv>,
+}
+
+/// Clocks configutation
+pub struct Config {
+    // base clock sources
+    pub msi: Option<MSIRange>,
+    pub hsi16: bool,
+    pub hse: Option<Hertz>,
+    #[cfg(not(any(stm32l47x, stm32l48x)))]
+    pub hsi48: bool,
+
+    // pll
+    pub pll: Option<Pll>,
+    pub pllsai1: Option<Pll>,
+    #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+    pub pllsai2: Option<Pll>,
+
+    // sysclk, buses.
+    pub mux: ClockSrc,
+    pub ahb_pre: AHBPrescaler,
+    pub apb1_pre: APBPrescaler,
+    pub apb2_pre: APBPrescaler,
+
+    // muxes
+    pub clk48_src: Clk48Src,
+
+    // low speed LSI/LSE/RTC
+    pub ls: super::LsConfig,
+}
+
+impl Default for Config {
+    #[inline]
+    fn default() -> Config {
+        Config {
+            hse: None,
+            hsi16: false,
+            msi: Some(MSIRange::RANGE4M),
+            mux: ClockSrc::MSI,
+            ahb_pre: AHBPrescaler::DIV1,
+            apb1_pre: APBPrescaler::DIV1,
+            apb2_pre: APBPrescaler::DIV1,
+            pll: None,
+            pllsai1: None,
+            #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+            pllsai2: None,
+            #[cfg(not(any(stm32l471, stm32l475, stm32l476, stm32l486)))]
+            hsi48: true,
+            clk48_src: Clk48Src::HSI48,
+            ls: Default::default(),
+        }
+    }
+}
+
+pub(crate) unsafe fn init(config: Config) {
+    // Switch to MSI to prevent problems with PLL configuration.
+    if !RCC.cr().read().msion() {
+        // Turn on MSI and configure it to 4MHz.
+        RCC.cr().modify(|w| {
+            w.set_msirgsel(Msirgsel::CR);
+            w.set_msirange(MSIRange::RANGE4M);
+            w.set_msipllen(false);
+            w.set_msion(true)
+        });
+
+        // Wait until MSI is running
+        while !RCC.cr().read().msirdy() {}
+    }
+    if RCC.cfgr().read().sws() != ClockSrc::MSI {
+        // Set MSI as a clock source, reset prescalers.
+        RCC.cfgr().write_value(Cfgr::default());
+        // Wait for clock switch status bits to change.
+        while RCC.cfgr().read().sws() != ClockSrc::MSI {}
+    }
+
+    #[cfg(stm32l5)]
+    crate::pac::PWR.cr1().modify(|w| {
+        w.set_vos(crate::pac::pwr::vals::Vos::RANGE0);
+    });
+
+    let rtc = config.ls.init();
+
+    let msi = config.msi.map(|range| {
+        // Enable MSI
+        RCC.cr().write(|w| {
+            w.set_msirange(range);
+            w.set_msirgsel(Msirgsel::CR);
+            w.set_msion(true);
+
+            // If LSE is enabled, enable calibration of MSI
+            w.set_msipllen(config.ls.lse.is_some());
+        });
+        while !RCC.cr().read().msirdy() {}
+
+        // Enable as clock source for USB, RNG if running at 48 MHz
+        if range == MSIRange::RANGE48M {}
+
+        msirange_to_hertz(range)
+    });
+
+    let hsi16 = config.hsi16.then(|| {
+        RCC.cr().write(|w| w.set_hsion(true));
+        while !RCC.cr().read().hsirdy() {}
+
+        HSI_FREQ
+    });
+
+    let hse = config.hse.map(|freq| {
+        RCC.cr().write(|w| w.set_hseon(true));
+        while !RCC.cr().read().hserdy() {}
+
+        freq
+    });
+
+    #[cfg(not(any(stm32l47x, stm32l48x)))]
+    let hsi48 = config.hsi48.then(|| {
+        RCC.crrcr().modify(|w| w.set_hsi48on(true));
+        while !RCC.crrcr().read().hsi48rdy() {}
+
+        Hertz(48_000_000)
+    });
+    #[cfg(any(stm32l47x, stm32l48x))]
+    let hsi48 = None;
+
+    let _plls = [
+        &config.pll,
+        &config.pllsai1,
+        #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+        &config.pllsai2,
+    ];
+
+    // L4 has shared PLLSRC, PLLM, check it's equal in all PLLs.
+    #[cfg(all(stm32l4, not(rcc_l4plus)))]
+    match get_equal(_plls.into_iter().flatten().map(|p| (p.source, p.prediv))) {
+        Err(()) => panic!("Source must be equal across all enabled PLLs."),
+        Ok(None) => {}
+        Ok(Some((source, prediv))) => RCC.pllcfgr().write(|w| {
+            w.set_pllm(prediv);
+            w.set_pllsrc(source);
+        }),
+    };
+
+    // L4+ has shared PLLSRC, check it's equal in all PLLs.
+    #[cfg(any(rcc_l4plus))]
+    match get_equal(_plls.into_iter().flatten().map(|p| p.source)) {
+        Err(()) => panic!("Source must be equal across all enabled PLLs."),
+        Ok(None) => {}
+        Ok(Some(source)) => RCC.pllcfgr().write(|w| {
+            w.set_pllsrc(source);
+        }),
+    };
+
+    let pll_input = PllInput { hse, hsi16, msi };
+    let pll = init_pll(PllInstance::Pll, config.pll, &pll_input);
+    let pllsai1 = init_pll(PllInstance::Pllsai1, config.pllsai1, &pll_input);
+    #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+    let _pllsai2 = init_pll(PllInstance::Pllsai2, config.pllsai2, &pll_input);
+
+    let sys_clk = match config.mux {
+        ClockSrc::HSE => hse.unwrap(),
+        ClockSrc::HSI16 => hsi16.unwrap(),
+        ClockSrc::MSI => msi.unwrap(),
+        ClockSrc::PLL => pll._r.unwrap(),
+    };
+
+    #[cfg(stm32l4)]
+    RCC.ccipr().modify(|w| w.set_clk48sel(config.clk48_src));
+    #[cfg(stm32l5)]
+    RCC.ccipr1().modify(|w| w.set_clk48sel(config.clk48_src));
+    let _clk48 = match config.clk48_src {
+        Clk48Src::HSI48 => hsi48,
+        Clk48Src::MSI => msi,
+        Clk48Src::PLLSAI1_Q => pllsai1._q,
+        Clk48Src::PLL_Q => pll._q,
+    };
+
+    #[cfg(rcc_l4plus)]
+    assert!(sys_clk.0 <= 120_000_000);
+    #[cfg(all(stm32l4, not(rcc_l4plus)))]
+    assert!(sys_clk.0 <= 80_000_000);
+
+    // Set flash wait states
+    #[cfg(stm32l4)]
+    FLASH.acr().modify(|w| {
+        w.set_latency(match sys_clk.0 {
+            0..=16_000_000 => 0,
+            0..=32_000_000 => 1,
+            0..=48_000_000 => 2,
+            0..=64_000_000 => 3,
+            _ => 4,
+        })
+    });
+    // VCORE Range 0 (performance), others TODO
+    #[cfg(stm32l5)]
+    FLASH.acr().modify(|w| {
+        w.set_latency(match sys_clk.0 {
+            0..=20_000_000 => 0,
+            0..=40_000_000 => 1,
+            0..=60_000_000 => 2,
+            0..=80_000_000 => 3,
+            0..=100_000_000 => 4,
+            _ => 5,
+        })
+    });
+
+    RCC.cfgr().modify(|w| {
+        w.set_sw(config.mux);
+        w.set_hpre(config.ahb_pre);
+        w.set_ppre1(config.apb1_pre);
+        w.set_ppre2(config.apb2_pre);
+    });
+
+    let ahb_freq = sys_clk / config.ahb_pre;
+
+    let (apb1_freq, apb1_tim_freq) = match config.apb1_pre {
+        APBPrescaler::DIV1 => (ahb_freq, ahb_freq),
+        pre => {
+            let freq = ahb_freq / pre;
+            (freq, freq * 2u32)
+        }
+    };
+
+    let (apb2_freq, apb2_tim_freq) = match config.apb2_pre {
+        APBPrescaler::DIV1 => (ahb_freq, ahb_freq),
+        pre => {
+            let freq = ahb_freq / pre;
+            (freq, freq * 2u32)
+        }
+    };
+
+    set_freqs(Clocks {
+        sys: sys_clk,
+        hclk1: ahb_freq,
+        hclk2: ahb_freq,
+        hclk3: ahb_freq,
+        pclk1: apb1_freq,
+        pclk2: apb2_freq,
+        pclk1_tim: apb1_tim_freq,
+        pclk2_tim: apb2_tim_freq,
+        rtc,
+    });
+}
+
+fn msirange_to_hertz(range: MSIRange) -> Hertz {
+    match range {
+        MSIRange::RANGE100K => Hertz(100_000),
+        MSIRange::RANGE200K => Hertz(200_000),
+        MSIRange::RANGE400K => Hertz(400_000),
+        MSIRange::RANGE800K => Hertz(800_000),
+        MSIRange::RANGE1M => Hertz(1_000_000),
+        MSIRange::RANGE2M => Hertz(2_000_000),
+        MSIRange::RANGE4M => Hertz(4_000_000),
+        MSIRange::RANGE8M => Hertz(8_000_000),
+        MSIRange::RANGE16M => Hertz(16_000_000),
+        MSIRange::RANGE24M => Hertz(24_000_000),
+        MSIRange::RANGE32M => Hertz(32_000_000),
+        MSIRange::RANGE48M => Hertz(48_000_000),
+        _ => unreachable!(),
+    }
+}
+
+#[allow(unused)]
+fn get_equal<T: Eq>(mut iter: impl Iterator<Item = T>) -> Result<Option<T>, ()> {
+    let Some(x) = iter.next() else { return Ok(None) };
+    if !iter.all(|y| y == x) {
+        return Err(());
+    }
+    return Ok(Some(x));
+}
+
+struct PllInput {
+    hsi16: Option<Hertz>,
+    hse: Option<Hertz>,
+    msi: Option<Hertz>,
+}
+
+#[derive(Default)]
+struct PllOutput {
+    _p: Option<Hertz>,
+    _q: Option<Hertz>,
+    _r: Option<Hertz>,
+}
+
+#[derive(PartialEq, Eq, Clone, Copy)]
+enum PllInstance {
+    Pll,
+    Pllsai1,
+    #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+    Pllsai2,
+}
+
+fn init_pll(instance: PllInstance, config: Option<Pll>, input: &PllInput) -> PllOutput {
+    // Disable PLL
+    match instance {
+        PllInstance::Pll => {
+            RCC.cr().modify(|w| w.set_pllon(false));
+            while RCC.cr().read().pllrdy() {}
+        }
+        PllInstance::Pllsai1 => {
+            RCC.cr().modify(|w| w.set_pllsai1on(false));
+            while RCC.cr().read().pllsai1rdy() {}
+        }
+        #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+        PllInstance::Pllsai2 => {
+            RCC.cr().modify(|w| w.set_pllsai2on(false));
+            while RCC.cr().read().pllsai2rdy() {}
+        }
+    }
+
+    let Some(pll) = config else { return PllOutput::default() };
+
+    let pll_src = match pll.source {
+        PLLSource::NONE => panic!("must not select PLL source as NONE"),
+        PLLSource::HSE => input.hse,
+        PLLSource::HSI16 => input.hsi16,
+        PLLSource::MSI => input.msi,
+    };
+
+    let pll_src = pll_src.unwrap();
+
+    let vco_freq = pll_src / pll.prediv * pll.mul;
+
+    let p = pll.divp.map(|div| vco_freq / div);
+    let q = pll.divq.map(|div| vco_freq / div);
+    let r = pll.divr.map(|div| vco_freq / div);
+
+    #[cfg(stm32l5)]
+    if instance == PllInstance::Pllsai2 {
+        assert!(q.is_none(), "PLLSAI2_Q is not available on L5");
+        assert!(r.is_none(), "PLLSAI2_R is not available on L5");
+    }
+
+    macro_rules! write_fields {
+        ($w:ident) => {
+            $w.set_plln(pll.mul);
+            if let Some(divp) = pll.divp {
+                $w.set_pllp(divp);
+                $w.set_pllpen(true);
+            }
+            if let Some(divq) = pll.divq {
+                $w.set_pllq(divq);
+                $w.set_pllqen(true);
+            }
+            if let Some(divr) = pll.divr {
+                $w.set_pllr(divr);
+                $w.set_pllren(true);
+            }
+        };
+    }
+
+    match instance {
+        PllInstance::Pll => RCC.pllcfgr().write(|w| {
+            w.set_pllm(pll.prediv);
+            w.set_pllsrc(pll.source);
+            write_fields!(w);
+        }),
+        PllInstance::Pllsai1 => RCC.pllsai1cfgr().write(|w| {
+            #[cfg(any(rcc_l4plus, stm32l5))]
+            w.set_pllm(pll.prediv);
+            #[cfg(stm32l5)]
+            w.set_pllsrc(pll.source);
+            write_fields!(w);
+        }),
+        #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+        PllInstance::Pllsai2 => RCC.pllsai2cfgr().write(|w| {
+            #[cfg(any(rcc_l4plus, stm32l5))]
+            w.set_pllm(pll.prediv);
+            #[cfg(stm32l5)]
+            w.set_pllsrc(pll.source);
+            write_fields!(w);
+        }),
+    }
+
+    // Enable PLL
+    match instance {
+        PllInstance::Pll => {
+            RCC.cr().modify(|w| w.set_pllon(true));
+            while !RCC.cr().read().pllrdy() {}
+        }
+        PllInstance::Pllsai1 => {
+            RCC.cr().modify(|w| w.set_pllsai1on(true));
+            while !RCC.cr().read().pllsai1rdy() {}
+        }
+        #[cfg(any(stm32l47x, stm32l48x, stm32l49x, stm32l4ax, rcc_l4plus, stm32l5))]
+        PllInstance::Pllsai2 => {
+            RCC.cr().modify(|w| w.set_pllsai2on(true));
+            while !RCC.cr().read().pllsai2rdy() {}
+        }
+    }
+
+    PllOutput { _p: p, _q: q, _r: r }
+}

embassy-stm32/src/rcc/l5.rs

@@ -1,291 +0,0 @@
-use crate::pac::rcc::regs::Cfgr;
-pub use crate::pac::rcc::vals::{
-    Hpre as AHBPrescaler, Msirange as MSIRange, Pllm as PllPreDiv, Plln as PllMul, Pllp as PllPDiv, Pllq as PllQDiv,
-    Pllr as PllRDiv, Ppre as APBPrescaler,
-};
-use crate::pac::rcc::vals::{Msirange, Pllsrc, Sw};
-use crate::pac::{FLASH, PWR, RCC};
-use crate::rcc::{set_freqs, Clocks};
-use crate::time::Hertz;
-
-/// HSI speed
-pub const HSI_FREQ: Hertz = Hertz(16_000_000);
-
-/// System clock mux source
-#[derive(Clone, Copy)]
-pub enum ClockSrc {
-    MSI(MSIRange),
-    PLL(PLLSource, PllRDiv, PllPreDiv, PllMul, Option<PllQDiv>),
-    HSE(Hertz),
-    HSI16,
-}
-
-/// PLL clock input source
-#[derive(Clone, Copy)]
-pub enum PLLSource {
-    HSI16,
-    HSE(Hertz),
-    MSI(MSIRange),
-}
-
-impl From<PLLSource> for Pllsrc {
-    fn from(val: PLLSource) -> Pllsrc {
-        match val {
-            PLLSource::HSI16 => Pllsrc::HSI16,
-            PLLSource::HSE(_) => Pllsrc::HSE,
-            PLLSource::MSI(_) => Pllsrc::MSI,
-        }
-    }
-}
-
-/// Clocks configutation
-pub struct Config {
-    pub mux: ClockSrc,
-    pub ahb_pre: AHBPrescaler,
-    pub apb1_pre: APBPrescaler,
-    pub apb2_pre: APBPrescaler,
-    pub pllsai1: Option<(PllMul, PllPreDiv, Option<PllRDiv>, Option<PllQDiv>, Option<PllPDiv>)>,
-    pub hsi48: bool,
-    pub ls: super::LsConfig,
-}
-
-impl Default for Config {
-    #[inline]
-    fn default() -> Config {
-        Config {
-            mux: ClockSrc::MSI(MSIRange::RANGE4M),
-            ahb_pre: AHBPrescaler::DIV1,
-            apb1_pre: APBPrescaler::DIV1,
-            apb2_pre: APBPrescaler::DIV1,
-            pllsai1: None,
-            hsi48: false,
-            ls: Default::default(),
-        }
-    }
-}
-
-pub(crate) unsafe fn init(config: Config) {
-    // Switch to MSI to prevent problems with PLL configuration.
-    if !RCC.cr().read().msion() {
-        // Turn on MSI and configure it to 4MHz.
-        RCC.cr().modify(|w| {
-            w.set_msirgsel(true); // MSI Range is provided by MSIRANGE[3:0].
-            w.set_msirange(MSIRange::RANGE4M);
-            w.set_msipllen(false);
-            w.set_msion(true)
-        });
-
-        // Wait until MSI is running
-        while !RCC.cr().read().msirdy() {}
-    }
-    if RCC.cfgr().read().sws() != Sw::MSI {
-        // Set MSI as a clock source, reset prescalers.
-        RCC.cfgr().write_value(Cfgr::default());
-        // Wait for clock switch status bits to change.
-        while RCC.cfgr().read().sws() != Sw::MSI {}
-    }
-
-    let rtc = config.ls.init();
-
-    PWR.cr1().modify(|w| w.set_vos(stm32_metapac::pwr::vals::Vos::RANGE0));
-    let (sys_clk, sw) = match config.mux {
-        ClockSrc::MSI(range) => {
-            // Enable MSI
-            RCC.cr().write(|w| {
-                w.set_msirange(range);
-                w.set_msirgsel(true);
-                w.set_msion(true);
-
-                // If LSE is enabled, enable calibration of MSI
-                w.set_msipllen(config.ls.lse.is_some());
-            });
-            while !RCC.cr().read().msirdy() {}
-
-            // Enable as clock source for USB, RNG if running at 48 MHz
-            if range == MSIRange::RANGE48M {
-                RCC.ccipr1().modify(|w| {
-                    w.set_clk48msel(0b11);
-                });
-            }
-            (msirange_to_hertz(range), Sw::MSI)
-        }
-        ClockSrc::HSI16 => {
-            // Enable HSI16
-            RCC.cr().write(|w| w.set_hsion(true));
-            while !RCC.cr().read().hsirdy() {}
-
-            (HSI_FREQ, Sw::HSI16)
-        }
-        ClockSrc::HSE(freq) => {
-            // Enable HSE
-            RCC.cr().write(|w| w.set_hseon(true));
-            while !RCC.cr().read().hserdy() {}
-
-            (freq, Sw::HSE)
-        }
-        ClockSrc::PLL(src, divr, prediv, mul, divq) => {
-            let src_freq = match src {
-                PLLSource::HSE(freq) => {
-                    // Enable HSE
-                    RCC.cr().write(|w| w.set_hseon(true));
-                    while !RCC.cr().read().hserdy() {}
-                    freq
-                }
-                PLLSource::HSI16 => {
-                    // Enable HSI
-                    RCC.cr().write(|w| w.set_hsion(true));
-                    while !RCC.cr().read().hsirdy() {}
-                    HSI_FREQ
-                }
-                PLLSource::MSI(range) => {
-                    // Enable MSI
-                    RCC.cr().write(|w| {
-                        w.set_msirange(range);
-                        w.set_msipllen(false); // should be turned on if LSE is started
-                        w.set_msirgsel(true);
-                        w.set_msion(true);
-                    });
-                    while !RCC.cr().read().msirdy() {}
-
-                    msirange_to_hertz(range)
-                }
-            };
-
-            // Disable PLL
-            RCC.cr().modify(|w| w.set_pllon(false));
-            while RCC.cr().read().pllrdy() {}
-
-            let freq = src_freq / prediv * mul / divr;
-
-            RCC.pllcfgr().write(move |w| {
-                w.set_plln(mul);
-                w.set_pllm(prediv);
-                w.set_pllr(divr);
-                if let Some(divq) = divq {
-                    w.set_pllq(divq);
-                    w.set_pllqen(true);
-                }
-                w.set_pllsrc(src.into());
-            });
-
-            // Enable as clock source for USB, RNG if PLL48 divisor is provided
-            if let Some(divq) = divq {
-                let freq = src_freq / prediv * mul / divq;
-                assert!(freq.0 == 48_000_000);
-                RCC.ccipr1().modify(|w| {
-                    w.set_clk48msel(0b10);
-                });
-            }
-
-            if let Some((mul, prediv, r_div, q_div, p_div)) = config.pllsai1 {
-                RCC.pllsai1cfgr().write(move |w| {
-                    w.set_plln(mul);
-                    w.set_pllm(prediv);
-                    if let Some(r_div) = r_div {
-                        w.set_pllr(r_div);
-                        w.set_pllren(true);
-                    }
-                    if let Some(q_div) = q_div {
-                        w.set_pllq(q_div);
-                        w.set_pllqen(true);
-                        let freq = src_freq / prediv * mul / q_div;
-                        if freq.0 == 48_000_000 {
-                            RCC.ccipr1().modify(|w| {
-                                w.set_clk48msel(0b1);
-                            });
-                        }
-                    }
-                    if let Some(p_div) = p_div {
-                        w.set_pllp(p_div);
-                        w.set_pllpen(true);
-                    }
-                });
-
-                RCC.cr().modify(|w| w.set_pllsai1on(true));
-            }
-
-            // Enable PLL
-            RCC.cr().modify(|w| w.set_pllon(true));
-            while !RCC.cr().read().pllrdy() {}
-            RCC.pllcfgr().modify(|w| w.set_pllren(true));
-
-            (freq, Sw::PLL)
-        }
-    };
-
-    if config.hsi48 {
-        RCC.crrcr().modify(|w| w.set_hsi48on(true));
-        while !RCC.crrcr().read().hsi48rdy() {}
-
-        // Enable as clock source for USB, RNG and SDMMC
-        RCC.ccipr1().modify(|w| w.set_clk48msel(0));
-    }
-
-    // Set flash wait states
-    // VCORE Range 0 (performance), others TODO
-    FLASH.acr().modify(|w| {
-        w.set_latency(match sys_clk.0 {
-            0..=20_000_000 => 0,
-            0..=40_000_000 => 1,
-            0..=60_000_000 => 2,
-            0..=80_000_000 => 3,
-            0..=100_000_000 => 4,
-            _ => 5,
-        })
-    });
-
-    RCC.cfgr().modify(|w| {
-        w.set_sw(sw);
-        w.set_hpre(config.ahb_pre);
-        w.set_ppre1(config.apb1_pre);
-        w.set_ppre2(config.apb2_pre);
-    });
-
-    let ahb_freq = sys_clk / config.ahb_pre;
-
-    let (apb1_freq, apb1_tim_freq) = match config.apb1_pre {
-        APBPrescaler::DIV1 => (ahb_freq, ahb_freq),
-        pre => {
-            let freq = ahb_freq / pre;
-            (freq, freq * 2u32)
-        }
-    };
-
-    let (apb2_freq, apb2_tim_freq) = match config.apb2_pre {
-        APBPrescaler::DIV1 => (ahb_freq, ahb_freq),
-        pre => {
-            let freq = ahb_freq / pre;
-            (freq, freq * 2u32)
-        }
-    };
-
-    set_freqs(Clocks {
-        sys: sys_clk,
-        ahb1: ahb_freq,
-        ahb2: ahb_freq,
-        ahb3: ahb_freq,
-        apb1: apb1_freq,
-        apb2: apb2_freq,
-        apb1_tim: apb1_tim_freq,
-        apb2_tim: apb2_tim_freq,
-        rtc,
-    });
-}
-
-fn msirange_to_hertz(range: Msirange) -> Hertz {
-    match range {
-        MSIRange::RANGE100K => Hertz(100_000),
-        MSIRange::RANGE200K => Hertz(200_000),
-        MSIRange::RANGE400K => Hertz(400_000),
-        MSIRange::RANGE800K => Hertz(800_000),
-        MSIRange::RANGE1M => Hertz(1_000_000),
-        MSIRange::RANGE2M => Hertz(2_000_000),
-        MSIRange::RANGE4M => Hertz(4_000_000),
-        MSIRange::RANGE8M => Hertz(8_000_000),
-        MSIRange::RANGE16M => Hertz(16_000_000),
-        MSIRange::RANGE24M => Hertz(24_000_000),
-        MSIRange::RANGE32M => Hertz(32_000_000),
-        MSIRange::RANGE48M => Hertz(48_000_000),
-        _ => unreachable!(),
-    }
-}

embassy-stm32/src/rcc/mod.rs

@@ -20,8 +20,7 @@ pub use mco::*;
 #[cfg_attr(rcc_g4, path = "g4.rs")]
 #[cfg_attr(any(rcc_h5, rcc_h50, rcc_h7, rcc_h7rm0433, rcc_h7ab), path = "h.rs")]
 #[cfg_attr(any(rcc_l0, rcc_l0_v2, rcc_l1), path = "l0l1.rs")]
-#[cfg_attr(rcc_l4, path = "l4.rs")]
+#[cfg_attr(any(rcc_l4, rcc_l4plus, rcc_l5), path = "l4l5.rs")]
-#[cfg_attr(rcc_l5, path = "l5.rs")]
 #[cfg_attr(rcc_u5, path = "u5.rs")]
 #[cfg_attr(rcc_wb, path = "wb.rs")]
 #[cfg_attr(rcc_wba, path = "wba.rs")]
@@ -48,23 +47,24 @@ pub struct Clocks {
     pub sys: Hertz,
 
     // APB
-    pub apb1: Hertz,
+    pub pclk1: Hertz,
-    pub apb1_tim: Hertz,
+    pub pclk1_tim: Hertz,
     #[cfg(not(any(rcc_c0, rcc_g0)))]
-    pub apb2: Hertz,
+    pub pclk2: Hertz,
     #[cfg(not(any(rcc_c0, rcc_g0)))]
-    pub apb2_tim: Hertz,
+    pub pclk2_tim: Hertz,
     #[cfg(any(rcc_wl5, rcc_wle, rcc_h5, rcc_h50, rcc_h7, rcc_h7rm0433, rcc_h7ab, rcc_u5))]
-    pub apb3: Hertz,
+    pub pclk3: Hertz,
-    #[cfg(any(rcc_h7, rcc_h7rm0433, rcc_h7ab))]
+    #[cfg(any(rcc_h7, rcc_h7rm0433, rcc_h7ab, stm32h5))]
-    pub apb4: Hertz,
+    pub pclk4: Hertz,
     #[cfg(any(rcc_wba))]
-    pub apb7: Hertz,
+    pub pclk7: Hertz,
 
     // AHB
-    pub ahb1: Hertz,
+    pub hclk1: Hertz,
     #[cfg(any(
         rcc_l4,
+        rcc_l4plus,
         rcc_l5,
         rcc_f2,
         rcc_f4,
@@ -82,9 +82,10 @@ pub struct Clocks {
         rcc_wl5,
         rcc_wle
     ))]
-    pub ahb2: Hertz,
+    pub hclk2: Hertz,
     #[cfg(any(
         rcc_l4,
+        rcc_l4plus,
         rcc_l5,
         rcc_f2,
         rcc_f4,
@@ -100,18 +101,36 @@ pub struct Clocks {
         rcc_wl5,
         rcc_wle
     ))]
-    pub ahb3: Hertz,
+    pub hclk3: Hertz,
     #[cfg(any(rcc_h5, rcc_h50, rcc_h7, rcc_h7rm0433, rcc_h7ab, rcc_wba))]
-    pub ahb4: Hertz,
+    pub hclk4: Hertz,
-
-    #[cfg(any(rcc_f2, rcc_f4, rcc_f410, rcc_f7))]
-    pub pll48: Option<Hertz>,
 
     #[cfg(all(rcc_f4, not(stm32f410)))]
-    pub plli2s: Option<Hertz>,
+    pub plli2s1_q: Option<Hertz>,
+    #[cfg(all(rcc_f4, not(stm32f410)))]
+    pub plli2s1_r: Option<Hertz>,
 
     #[cfg(any(stm32f427, stm32f429, stm32f437, stm32f439, stm32f446, stm32f469, stm32f479))]
-    pub pllsai: Option<Hertz>,
+    pub pllsai1_q: Option<Hertz>,
+    #[cfg(any(stm32f427, stm32f429, stm32f437, stm32f439, stm32f446, stm32f469, stm32f479))]
+    pub pllsai1_r: Option<Hertz>,
+
+    #[cfg(stm32g4)]
+    pub pll1_p: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7, rcc_f2, rcc_f4, rcc_f410, rcc_f7))]
+    pub pll1_q: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
+    pub pll2_p: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
+    pub pll2_q: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
+    pub pll2_r: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
+    pub pll3_p: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
+    pub pll3_q: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
+    pub pll3_r: Option<Hertz>,
 
     #[cfg(any(
         rcc_f1,
@@ -135,51 +154,27 @@ pub struct Clocks {
 
     pub rtc: Option<Hertz>,
 
+    #[cfg(any(stm32h5, stm32h7))]
+    pub hsi: Option<Hertz>,
     #[cfg(stm32h5)]
-    pub mux_rcc_pclk1: Option<Hertz>,
+    pub hsi48: Option<Hertz>,
     #[cfg(stm32h5)]
-    pub mux_pll2_q: Option<Hertz>,
+    pub lsi: Option<Hertz>,
-    #[cfg(stm32h5)]
+    #[cfg(any(stm32h5, stm32h7))]
-    pub mux_pll3_q: Option<Hertz>,
+    pub csi: Option<Hertz>,
-    #[cfg(stm32h5)]
+
-    pub mux_hsi_ker: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
-    #[cfg(stm32h5)]
+    pub lse: Option<Hertz>,
-    pub mux_csi_ker: Option<Hertz>,
+    #[cfg(any(stm32h5, stm32h7))]
-    #[cfg(stm32h5)]
+    pub hse: Option<Hertz>,
-    pub mux_lse: Option<Hertz>,
 
     #[cfg(stm32h5)]
-    pub mux_pll1_q: Option<Hertz>,
+    pub audioclk: Option<Hertz>,
-    #[cfg(stm32h5)]
+    #[cfg(any(stm32h5, stm32h7))]
-    pub mux_pll2_p: Option<Hertz>,
+    pub per: Option<Hertz>,
-    #[cfg(rcc_h5)]
-    pub mux_pll3_p: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_audioclk: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_per: Option<Hertz>,
 
-    #[cfg(stm32h5)]
+    #[cfg(stm32h7)]
-    pub mux_pll3_r: Option<Hertz>,
+    pub rcc_pclk_d3: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_rcc_pclk3: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_pll3_1: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_hsi48_ker: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_lsi_ker: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_pll2_r: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_rcc_pclk2: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_rcc_pclk4: Option<Hertz>,
-    #[cfg(stm32h5)]
-    pub mux_hse: Option<Hertz>,
-
-    #[cfg(stm32h5)]
-    pub mux_hsi48: Option<Hertz>,
 }
 
 #[cfg(feature = "low-power")]

embassy-stm32/src/rcc/u5.rs

@@ -188,7 +188,7 @@ impl Default for Config {
             apb1_pre: APBPrescaler::DIV1,
             apb2_pre: APBPrescaler::DIV1,
             apb3_pre: APBPrescaler::DIV1,
-            hsi48: false,
+            hsi48: true,
             voltage_range: VoltageScale::RANGE3,
             ls: Default::default(),
         }
@@ -436,14 +436,14 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        ahb2: ahb_freq,
+        hclk2: ahb_freq,
-        ahb3: ahb_freq,
+        hclk3: ahb_freq,
-        apb1: apb1_freq,
+        pclk1: apb1_freq,
-        apb2: apb2_freq,
+        pclk2: apb2_freq,
-        apb3: apb3_freq,
+        pclk3: apb3_freq,
-        apb1_tim: apb1_tim_freq,
+        pclk1_tim: apb1_tim_freq,
-        apb2_tim: apb2_tim_freq,
+        pclk2_tim: apb2_tim_freq,
         rtc,
     });
 }

embassy-stm32/src/rcc/wb.rs

@@ -40,6 +40,7 @@ pub struct Config {
     pub hse: Option<Hse>,
     pub sys: Sysclk,
     pub mux: Option<PllMux>,
+    pub hsi48: bool,
 
     pub pll: Option<Pll>,
     pub pllsai: Option<Pll>,
@@ -63,6 +64,7 @@ pub const WPAN_DEFAULT: Config = Config {
         source: PllSource::HSE,
         prediv: Pllm::DIV2,
     }),
+    hsi48: true,
 
     ls: super::LsConfig::default_lse(),
 
@@ -90,6 +92,7 @@ impl Default for Config {
             mux: None,
             pll: None,
             pllsai: None,
+            hsi48: true,
 
             ls: Default::default(),
 
@@ -222,6 +225,13 @@ pub(crate) unsafe fn init(config: Config) {
         _ => {}
     }
 
+    let _hsi48 = config.hsi48.then(|| {
+        rcc.crrcr().modify(|w| w.set_hsi48on(true));
+        while !rcc.crrcr().read().hsi48rdy() {}
+
+        Hertz(48_000_000)
+    });
+
     rcc.cfgr().modify(|w| {
         w.set_sw(config.sys.into());
         w.set_hpre(config.ahb1_pre);
@@ -236,13 +246,13 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb1_clk,
+        hclk1: ahb1_clk,
-        ahb2: ahb2_clk,
+        hclk2: ahb2_clk,
-        ahb3: ahb3_clk,
+        hclk3: ahb3_clk,
-        apb1: apb1_clk,
+        pclk1: apb1_clk,
-        apb2: apb2_clk,
+        pclk2: apb2_clk,
-        apb1_tim: apb1_tim_clk,
+        pclk1_tim: apb1_tim_clk,
-        apb2_tim: apb2_tim_clk,
+        pclk2_tim: apb2_tim_clk,
         rtc,
     })
 }

embassy-stm32/src/rcc/wba.rs

@@ -142,14 +142,14 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        ahb2: ahb_freq,
+        hclk2: ahb_freq,
-        ahb4: ahb_freq,
+        hclk4: ahb_freq,
-        apb1: apb1_freq,
+        pclk1: apb1_freq,
-        apb2: apb2_freq,
+        pclk2: apb2_freq,
-        apb7: apb7_freq,
+        pclk7: apb7_freq,
-        apb1_tim: apb1_tim_freq,
+        pclk1_tim: apb1_tim_freq,
-        apb2_tim: apb2_tim_freq,
+        pclk2_tim: apb2_tim_freq,
         rtc,
     });
 }

embassy-stm32/src/rcc/wl.rs

@@ -145,14 +145,14 @@ pub(crate) unsafe fn init(config: Config) {
 
     set_freqs(Clocks {
         sys: sys_clk,
-        ahb1: ahb_freq,
+        hclk1: ahb_freq,
-        ahb2: ahb_freq,
+        hclk2: ahb_freq,
-        ahb3: shd_ahb_freq,
+        hclk3: shd_ahb_freq,
-        apb1: apb1_freq,
+        pclk1: apb1_freq,
-        apb2: apb2_freq,
+        pclk2: apb2_freq,
-        apb3: shd_ahb_freq,
+        pclk3: shd_ahb_freq,
-        apb1_tim: apb1_tim_freq,
+        pclk1_tim: apb1_tim_freq,
-        apb2_tim: apb2_tim_freq,
+        pclk2_tim: apb2_tim_freq,
         rtc,
     });
 }

embassy-stm32/src/rng.rs

@@ -85,7 +85,7 @@ impl<'d, T: Instance> Rng<'d, T> {
             reg.set_ie(false);
             reg.set_rngen(true);
         });
-        T::regs().cr().write(|reg| {
+        T::regs().cr().modify(|reg| {
             reg.set_ced(false);
         });
         // wait for CONDRST to be set

embassy-stm32/src/sdmmc/mod.rs

@@ -1457,7 +1457,7 @@ cfg_if::cfg_if! {
         macro_rules! kernel_clk {
             ($inst:ident) => {
                 critical_section::with(|_| unsafe {
-                    crate::rcc::get_freqs().pll48
+                    crate::rcc::get_freqs().pll1_q
                 }).expect("PLL48 is required for SDIO")
             }
         }
@@ -1469,7 +1469,7 @@ cfg_if::cfg_if! {
                     if sdmmcsel == crate::pac::rcc::vals::Sdmmcsel::SYSCLK {
                         crate::rcc::get_freqs().sys
                     } else {
-                        crate::rcc::get_freqs().pll48.expect("PLL48 is required for SDMMC")
+                        crate::rcc::get_freqs().pll1_q.expect("PLL48 is required for SDMMC")
                     }
                 })
             };
@@ -1479,7 +1479,7 @@ cfg_if::cfg_if! {
                     if sdmmcsel == crate::pac::rcc::vals::Sdmmcsel::SYSCLK {
                         crate::rcc::get_freqs().sys
                     } else {
-                        crate::rcc::get_freqs().pll48.expect("PLL48 is required for SDMMC")
+                        crate::rcc::get_freqs().pll1_q.expect("PLL48 is required for SDMMC")
                     }
                 })
             };

embassy-stm32/src/spi/mod.rs

@@ -322,7 +322,7 @@ impl<'d, T: Instance, Tx, Rx> Spi<'d, T, Tx, Rx> {
     }
 
     /// Reconfigures it with the supplied config.
-    fn set_config(&mut self, config: Config) {
+    pub fn set_config(&mut self, config: &Config) -> Result<(), ()> {
         let cpha = config.raw_phase();
         let cpol = config.raw_polarity();
 
@@ -351,6 +351,7 @@ impl<'d, T: Instance, Tx, Rx> Spi<'d, T, Tx, Rx> {
                 w.set_mbr(br);
             });
         }
+        Ok(())
     }
 
     pub fn get_current_config(&self) -> Config {
@@ -1062,8 +1063,6 @@ impl<'d, T: Instance, Tx, Rx> SetConfig for Spi<'d, T, Tx, Rx> {
     type Config = Config;
     type ConfigError = ();
     fn set_config(&mut self, config: &Self::Config) -> Result<(), ()> {
-        self.set_config(*config);
+        self.set_config(config)
-
-        Ok(())
     }
 }

embassy-stm32/src/timer/complementary_pwm.rs

@@ -71,7 +71,7 @@ impl<'d, T: ComplementaryCaptureCompare16bitInstance> ComplementaryPwm<'d, T> {
         this.inner.set_frequency(freq);
         this.inner.start();
 
-        this.inner.enable_outputs(true);
+        this.inner.enable_outputs();
 
         this.inner
             .set_output_compare_mode(Channel::Ch1, OutputCompareMode::PwmMode1);

embassy-stm32/src/timer/mod.rs

@@ -173,7 +173,7 @@ pub(crate) mod sealed {
                 }
             });
         }
-        fn enable_outputs(&mut self, _enable: bool) {}
+        fn enable_outputs(&mut self);
 
         fn set_output_compare_mode(&mut self, channel: Channel, mode: OutputCompareMode) {
             let r = Self::regs_gp16();
@@ -401,7 +401,9 @@ macro_rules! impl_32bit_timer {
 #[allow(unused)]
 macro_rules! impl_compare_capable_16bit {
     ($inst:ident) => {
-        impl sealed::CaptureCompare16bitInstance for crate::peripherals::$inst {}
+        impl sealed::CaptureCompare16bitInstance for crate::peripherals::$inst {
+            fn enable_outputs(&mut self) {}
+        }
     };
 }
 
@@ -450,7 +452,13 @@ foreach_interrupt! {
         impl CaptureCompare16bitInstance for crate::peripherals::$inst {}
         impl ComplementaryCaptureCompare16bitInstance for crate::peripherals::$inst {}
         impl AdvancedControlInstance for crate::peripherals::$inst {}
-        impl sealed::CaptureCompare16bitInstance for crate::peripherals::$inst {}
+        impl sealed::CaptureCompare16bitInstance for crate::peripherals::$inst {
+            fn enable_outputs(&mut self) {
+                use crate::timer::sealed::AdvancedControlInstance;
+                let r = Self::regs_advanced();
+                r.bdtr().modify(|w| w.set_moe(true));
+            }
+        }
         impl sealed::ComplementaryCaptureCompare16bitInstance for crate::peripherals::$inst {}
         impl sealed::GeneralPurpose16bitInstance for crate::peripherals::$inst {
             fn regs_gp16() -> crate::pac::timer::TimGp16 {

embassy-stm32/src/timer/simple_pwm.rs

@@ -70,7 +70,7 @@ impl<'d, T: CaptureCompare16bitInstance> SimplePwm<'d, T> {
         this.inner.set_frequency(freq);
         this.inner.start();
 
-        this.inner.enable_outputs(true);
+        this.inner.enable_outputs();
 
         this.inner
             .set_output_compare_mode(Channel::Ch1, OutputCompareMode::PwmMode1);

embassy-stm32/src/usart/buffered.rs

@@ -253,7 +253,7 @@ impl<'d, T: BasicInstance> BufferedUart<'d, T> {
         (self.tx, self.rx)
     }
 
-    fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
+    pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
         reconfigure::<T>(config)
     }
 }
@@ -333,7 +333,7 @@ impl<'d, T: BasicInstance> BufferedUartRx<'d, T> {
         }
     }
 
-    fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
+    pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
         reconfigure::<T>(config)
     }
 }
@@ -407,7 +407,7 @@ impl<'d, T: BasicInstance> BufferedUartTx<'d, T> {
         }
     }
 
-    fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
+    pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
         reconfigure::<T>(config)
     }
 }

embassy-stm32/src/usart/mod.rs

@@ -274,7 +274,7 @@ impl<'d, T: BasicInstance, TxDma> UartTx<'d, T, TxDma> {
         })
     }
 
-    fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
+    pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
         reconfigure::<T>(config)
     }
 
@@ -373,7 +373,7 @@ impl<'d, T: BasicInstance, RxDma> UartRx<'d, T, RxDma> {
         })
     }
 
-    fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
+    pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
         reconfigure::<T>(config)
     }
 

embassy-stm32/src/usart/ringbuffered.rs

@@ -64,7 +64,7 @@ impl<'d, T: BasicInstance, RxDma: super::RxDma<T>> RingBufferedUartRx<'d, T, RxD
         Err(err)
     }
 
-    fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
+    pub fn set_config(&mut self, config: &Config) -> Result<(), ConfigError> {
         self.teardown_uart();
         reconfigure::<T>(config)
     }

embassy-time/CHANGELOG.md

@@ -5,6 +5,13 @@ All notable changes to this project will be documented in this file.
 The format is based on [Keep a Changelog](https://keepachangelog.com/en/1.0.0/),
 and this project adheres to [Semantic Versioning](https://semver.org/spec/v2.0.0.html).
 
+## 0.1.5 - 2023-10-16
+
+- Added `links` key to Cargo.toml, to prevent multiple copies of this crate in the same binary.
+  Needed because different copies might get different tick rates, causing
+  wrong delays if the time driver is using one copy and user code is using another.
+  This is especially common when mixing crates from crates.io and git.
+
 ## 0.1.4 - 2023-10-12
 
 - Added more tick rates

embassy-time/Cargo.toml

@@ -1,6 +1,6 @@
 [package]
 name = "embassy-time"
-version = "0.1.4"
+version = "0.1.5"
 edition = "2021"
 description = "Instant and Duration for embedded no-std systems, with async timer support"
 repository = "https://github.com/embassy-rs/embassy"
@@ -13,6 +13,12 @@ categories = [
     "asynchronous",
 ]
 
+# Prevent multiple copies of this crate in the same binary.
+# Needed because different copies might get different tick rates, causing
+# wrong delays if the time driver is using one copy and user code is using another.
+# This is especially common when mixing crates from crates.io and git.
+links = "embassy-time"
+
 [package.metadata.embassy_docs]
 src_base = "https://github.com/embassy-rs/embassy/blob/embassy-time-v$VERSION/embassy-time/src/"
 src_base_git = "https://github.com/embassy-rs/embassy/blob/$COMMIT/embassy-time/src/"

embassy-time/build.rs

@@ -0,0 +1,3 @@
+// empty, needed to be able to use `links` in Cargo.toml.
+
+fn main() {}

embassy-time/src/delay.rs

@@ -36,11 +36,11 @@ mod eha {
 
     impl embedded_hal_async::delay::DelayUs for Delay {
         async fn delay_us(&mut self, micros: u32) {
-            Timer::after(Duration::from_micros(micros as _)).await
+            Timer::after_micros(micros as _).await
         }
 
         async fn delay_ms(&mut self, millis: u32) {
-            Timer::after(Duration::from_millis(millis as _)).await
+            Timer::after_millis(millis as _).await
         }
     }
 }

embassy-time/src/timer.rs

@@ -64,6 +64,42 @@ impl Timer {
             yielded_once: false,
         }
     }
+
+    /// Expire after the specified number of ticks.
+    ///
+    /// This method is a convenience wrapper for calling `Timer::after(Duration::from_ticks())`.
+    /// For more details, refer to [`Timer::after()`] and [`Duration::from_ticks()`].
+    #[inline]
+    pub fn after_ticks(ticks: u64) -> Self {
+        Self::after(Duration::from_ticks(ticks))
+    }
+
+    /// Expire after the specified number of microseconds.
+    ///
+    /// This method is a convenience wrapper for calling `Timer::after(Duration::from_micros())`.
+    /// For more details, refer to [`Timer::after()`] and [`Duration::from_micros()`].
+    #[inline]
+    pub fn after_micros(micros: u64) -> Self {
+        Self::after(Duration::from_micros(micros))
+    }
+
+    /// Expire after the specified number of milliseconds.
+    ///
+    /// This method is a convenience wrapper for calling `Timer::after(Duration::from_millis())`.
+    /// For more details, refer to [`Timer::after`] and [`Duration::from_millis()`].
+    #[inline]
+    pub fn after_millis(millis: u64) -> Self {
+        Self::after(Duration::from_millis(millis))
+    }
+
+    /// Expire after the specified number of seconds.
+    ///
+    /// This method is a convenience wrapper for calling `Timer::after(Duration::from_secs())`.
+    /// For more details, refer to [`Timer::after`] and [`Duration::from_secs()`].
+    #[inline]
+    pub fn after_secs(secs: u64) -> Self {
+        Self::after(Duration::from_secs(secs))
+    }
 }
 
 impl Unpin for Timer {}

embassy-usb/src/class/midi.rs

@@ -0,0 +1,227 @@
+//! MIDI class implementation.
+
+use crate::driver::{Driver, Endpoint, EndpointError, EndpointIn, EndpointOut};
+use crate::Builder;
+
+/// This should be used as `device_class` when building the `UsbDevice`.
+pub const USB_AUDIO_CLASS: u8 = 0x01;
+
+const USB_AUDIOCONTROL_SUBCLASS: u8 = 0x01;
+const USB_MIDISTREAMING_SUBCLASS: u8 = 0x03;
+const MIDI_IN_JACK_SUBTYPE: u8 = 0x02;
+const MIDI_OUT_JACK_SUBTYPE: u8 = 0x03;
+const EMBEDDED: u8 = 0x01;
+const EXTERNAL: u8 = 0x02;
+const CS_INTERFACE: u8 = 0x24;
+const CS_ENDPOINT: u8 = 0x25;
+const HEADER_SUBTYPE: u8 = 0x01;
+const MS_HEADER_SUBTYPE: u8 = 0x01;
+const MS_GENERAL: u8 = 0x01;
+const PROTOCOL_NONE: u8 = 0x00;
+const MIDI_IN_SIZE: u8 = 0x06;
+const MIDI_OUT_SIZE: u8 = 0x09;
+
+/// Packet level implementation of a USB MIDI device.
+///
+/// This class can be used directly and it has the least overhead due to directly reading and
+/// writing USB packets with no intermediate buffers, but it will not act like a stream-like port.
+/// The following constraints must be followed if you use this class directly:
+///
+/// - `read_packet` must be called with a buffer large enough to hold max_packet_size bytes.
+/// - `write_packet` must not be called with a buffer larger than max_packet_size bytes.
+/// - If you write a packet that is exactly max_packet_size bytes long, it won't be processed by the
+///   host operating system until a subsequent shorter packet is sent. A zero-length packet (ZLP)
+///   can be sent if there is no other data to send. This is because USB bulk transactions must be
+///   terminated with a short packet, even if the bulk endpoint is used for stream-like data.
+pub struct MidiClass<'d, D: Driver<'d>> {
+    read_ep: D::EndpointOut,
+    write_ep: D::EndpointIn,
+}
+
+impl<'d, D: Driver<'d>> MidiClass<'d, D> {
+    /// Creates a new MidiClass with the provided UsbBus, number of input and output jacks and max_packet_size in bytes.
+    /// For full-speed devices, max_packet_size has to be one of 8, 16, 32 or 64.
+    pub fn new(builder: &mut Builder<'d, D>, n_in_jacks: u8, n_out_jacks: u8, max_packet_size: u16) -> Self {
+        let mut func = builder.function(USB_AUDIO_CLASS, USB_AUDIOCONTROL_SUBCLASS, PROTOCOL_NONE);
+
+        // Audio control interface
+        let mut iface = func.interface();
+        let audio_if = iface.interface_number();
+        let midi_if = u8::from(audio_if) + 1;
+        let mut alt = iface.alt_setting(USB_AUDIO_CLASS, USB_AUDIOCONTROL_SUBCLASS, PROTOCOL_NONE, None);
+        alt.descriptor(CS_INTERFACE, &[HEADER_SUBTYPE, 0x00, 0x01, 0x09, 0x00, 0x01, midi_if]);
+
+        // MIDIStreaming interface
+        let mut iface = func.interface();
+        let _midi_if = iface.interface_number();
+        let mut alt = iface.alt_setting(USB_AUDIO_CLASS, USB_MIDISTREAMING_SUBCLASS, PROTOCOL_NONE, None);
+
+        let midi_streaming_total_length = 7
+            + (n_in_jacks + n_out_jacks) as usize * (MIDI_IN_SIZE + MIDI_OUT_SIZE) as usize
+            + 7
+            + (4 + n_out_jacks as usize)
+            + 7
+            + (4 + n_in_jacks as usize);
+
+        alt.descriptor(
+            CS_INTERFACE,
+            &[
+                MS_HEADER_SUBTYPE,
+                0x00,
+                0x01,
+                (midi_streaming_total_length & 0xFF) as u8,
+                ((midi_streaming_total_length >> 8) & 0xFF) as u8,
+            ],
+        );
+
+        // Calculates the index'th external midi in jack id
+        let in_jack_id_ext = |index| 2 * index + 1;
+        // Calculates the index'th embedded midi out jack id
+        let out_jack_id_emb = |index| 2 * index + 2;
+        // Calculates the index'th external midi out jack id
+        let out_jack_id_ext = |index| 2 * n_in_jacks + 2 * index + 1;
+        // Calculates the index'th embedded midi in jack id
+        let in_jack_id_emb = |index| 2 * n_in_jacks + 2 * index + 2;
+
+        for i in 0..n_in_jacks {
+            alt.descriptor(CS_INTERFACE, &[MIDI_IN_JACK_SUBTYPE, EXTERNAL, in_jack_id_ext(i), 0x00]);
+        }
+
+        for i in 0..n_out_jacks {
+            alt.descriptor(CS_INTERFACE, &[MIDI_IN_JACK_SUBTYPE, EMBEDDED, in_jack_id_emb(i), 0x00]);
+        }
+
+        for i in 0..n_out_jacks {
+            alt.descriptor(
+                CS_INTERFACE,
+                &[
+                    MIDI_OUT_JACK_SUBTYPE,
+                    EXTERNAL,
+                    out_jack_id_ext(i),
+                    0x01,
+                    in_jack_id_emb(i),
+                    0x01,
+                    0x00,
+                ],
+            );
+        }
+
+        for i in 0..n_in_jacks {
+            alt.descriptor(
+                CS_INTERFACE,
+                &[
+                    MIDI_OUT_JACK_SUBTYPE,
+                    EMBEDDED,
+                    out_jack_id_emb(i),
+                    0x01,
+                    in_jack_id_ext(i),
+                    0x01,
+                    0x00,
+                ],
+            );
+        }
+
+        let mut endpoint_data = [
+            MS_GENERAL, 0, // Number of jacks
+            0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, // Jack mappings
+        ];
+        endpoint_data[1] = n_out_jacks;
+        for i in 0..n_out_jacks {
+            endpoint_data[2 + i as usize] = in_jack_id_emb(i);
+        }
+        let read_ep = alt.endpoint_bulk_out(max_packet_size);
+        alt.descriptor(CS_ENDPOINT, &endpoint_data[0..2 + n_out_jacks as usize]);
+
+        endpoint_data[1] = n_in_jacks;
+        for i in 0..n_in_jacks {
+            endpoint_data[2 + i as usize] = out_jack_id_emb(i);
+        }
+        let write_ep = alt.endpoint_bulk_in(max_packet_size);
+        alt.descriptor(CS_ENDPOINT, &endpoint_data[0..2 + n_in_jacks as usize]);
+
+        MidiClass { read_ep, write_ep }
+    }
+
+    /// Gets the maximum packet size in bytes.
+    pub fn max_packet_size(&self) -> u16 {
+        // The size is the same for both endpoints.
+        self.read_ep.info().max_packet_size
+    }
+
+    /// Writes a single packet into the IN endpoint.
+    pub async fn write_packet(&mut self, data: &[u8]) -> Result<(), EndpointError> {
+        self.write_ep.write(data).await
+    }
+
+    /// Reads a single packet from the OUT endpoint.
+    pub async fn read_packet(&mut self, data: &mut [u8]) -> Result<usize, EndpointError> {
+        self.read_ep.read(data).await
+    }
+
+    /// Waits for the USB host to enable this interface
+    pub async fn wait_connection(&mut self) {
+        self.read_ep.wait_enabled().await
+    }
+
+    /// Split the class into a sender and receiver.
+    ///
+    /// This allows concurrently sending and receiving packets from separate tasks.
+    pub fn split(self) -> (Sender<'d, D>, Receiver<'d, D>) {
+        (
+            Sender {
+                write_ep: self.write_ep,
+            },
+            Receiver { read_ep: self.read_ep },
+        )
+    }
+}
+
+/// Midi class packet sender.
+///
+/// You can obtain a `Sender` with [`MidiClass::split`]
+pub struct Sender<'d, D: Driver<'d>> {
+    write_ep: D::EndpointIn,
+}
+
+impl<'d, D: Driver<'d>> Sender<'d, D> {
+    /// Gets the maximum packet size in bytes.
+    pub fn max_packet_size(&self) -> u16 {
+        // The size is the same for both endpoints.
+        self.write_ep.info().max_packet_size
+    }
+
+    /// Writes a single packet.
+    pub async fn write_packet(&mut self, data: &[u8]) -> Result<(), EndpointError> {
+        self.write_ep.write(data).await
+    }
+
+    /// Waits for the USB host to enable this interface
+    pub async fn wait_connection(&mut self) {
+        self.write_ep.wait_enabled().await
+    }
+}
+
+/// Midi class packet receiver.
+///
+/// You can obtain a `Receiver` with [`MidiClass::split`]
+pub struct Receiver<'d, D: Driver<'d>> {
+    read_ep: D::EndpointOut,
+}
+
+impl<'d, D: Driver<'d>> Receiver<'d, D> {
+    /// Gets the maximum packet size in bytes.
+    pub fn max_packet_size(&self) -> u16 {
+        // The size is the same for both endpoints.
+        self.read_ep.info().max_packet_size
+    }
+
+    /// Reads a single packet.
+    pub async fn read_packet(&mut self, data: &mut [u8]) -> Result<usize, EndpointError> {
+        self.read_ep.read(data).await
+    }
+
+    /// Waits for the USB host to enable this interface
+    pub async fn wait_connection(&mut self) {
+        self.read_ep.wait_enabled().await
+    }
+}

embassy-usb/src/class/mod.rs

@@ -2,3 +2,4 @@
 pub mod cdc_acm;
 pub mod cdc_ncm;
 pub mod hid;
+pub mod midi;

examples/boot/application/nrf/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers", "arch-cortex-m", "executor-thread"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly"] }
 embassy-nrf = { version = "0.1.0", path = "../../../../embassy-nrf", features = ["time-driver-rtc1", "gpiote", "nightly"] }
 embassy-boot = { version = "0.1.0", path = "../../../../embassy-boot/boot", features = ["nightly"] }
 embassy-boot-nrf = { version = "0.1.0", path = "../../../../embassy-boot/nrf", features = ["nightly"] }

examples/boot/application/nrf/src/bin/b.rs

@@ -5,7 +5,7 @@
 
 use embassy_executor::Spawner;
 use embassy_nrf::gpio::{Level, Output, OutputDrive};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
@@ -19,8 +19,8 @@ async fn main(_spawner: Spawner) {
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(300)).await;
+        Timer::after_millis(300).await;
         led.set_low();
-        Timer::after(Duration::from_millis(300)).await;
+        Timer::after_millis(300).await;
     }
 }

examples/boot/application/rp/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers", "arch-cortex-m", "executor-thread"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly"] }
 embassy-rp = { version = "0.1.0", path = "../../../../embassy-rp", features = ["time-driver", "unstable-traits", "nightly"] }
 embassy-boot-rp = { version = "0.1.0", path = "../../../../embassy-boot/rp", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/rp/src/bin/a.rs

@@ -41,7 +41,7 @@ async fn main(_s: Spawner) {
     let mut aligned = AlignedBuffer([0; 1]);
     let mut updater = BlockingFirmwareUpdater::new(config, &mut aligned.0);
 
-    Timer::after(Duration::from_secs(5)).await;
+    Timer::after_secs(5).await;
     watchdog.feed();
     led.set_high();
     let mut offset = 0;
@@ -61,7 +61,7 @@ async fn main(_s: Spawner) {
     watchdog.feed();
     defmt::info!("firmware written, marking update");
     updater.mark_updated().unwrap();
-    Timer::after(Duration::from_secs(2)).await;
+    Timer::after_secs(2).await;
     led.set_low();
     defmt::info!("update marked, resetting");
     cortex_m::peripheral::SCB::sys_reset();

examples/boot/application/rp/src/bin/b.rs

@@ -4,7 +4,7 @@
 
 use embassy_executor::Spawner;
 use embassy_rp::gpio;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use gpio::{Level, Output};
 use {defmt_rtt as _, panic_reset as _};
 
@@ -15,9 +15,9 @@ async fn main(_s: Spawner) {
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(100)).await;
+        Timer::after_millis(100).await;
     }
 }

examples/boot/application/stm32f3/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
 embassy-stm32 = { version = "0.1.0", path = "../../../../embassy-stm32", features = ["unstable-traits", "nightly", "stm32f303re", "time-driver-any", "exti"]  }
 embassy-boot-stm32 = { version = "0.1.0", path = "../../../../embassy-boot/stm32", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/stm32f3/src/bin/b.rs

@@ -6,7 +6,7 @@
 use defmt_rtt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
@@ -16,9 +16,9 @@ async fn main(_spawner: Spawner) {
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
     }
 }

examples/boot/application/stm32f7/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
 embassy-stm32 = { version = "0.1.0", path = "../../../../embassy-stm32", features = ["unstable-traits", "nightly", "stm32f767zi", "time-driver-any", "exti"]  }
 embassy-boot-stm32 = { version = "0.1.0", path = "../../../../embassy-boot/stm32", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/stm32f7/src/bin/b.rs

@@ -6,21 +6,21 @@
 use defmt_rtt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
 async fn main(_spawner: Spawner) {
     let p = embassy_stm32::init(Default::default());
-    Timer::after(Duration::from_millis(300)).await;
+    Timer::after_millis(300).await;
     let mut led = Output::new(p.PB7, Level::High, Speed::Low);
     led.set_high();
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
     }
 }

examples/boot/application/stm32h7/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
 embassy-stm32 = { version = "0.1.0", path = "../../../../embassy-stm32", features = ["unstable-traits", "nightly", "stm32h743zi", "time-driver-any", "exti"]  }
 embassy-boot-stm32 = { version = "0.1.0", path = "../../../../embassy-boot/stm32", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/stm32h7/src/bin/b.rs

@@ -6,21 +6,21 @@
 use defmt_rtt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
 async fn main(_spawner: Spawner) {
     let p = embassy_stm32::init(Default::default());
-    Timer::after(Duration::from_millis(300)).await;
+    Timer::after_millis(300).await;
     let mut led = Output::new(p.PB14, Level::High, Speed::Low);
     led.set_high();
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
     }
 }

examples/boot/application/stm32l0/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
 embassy-stm32 = { version = "0.1.0", path = "../../../../embassy-stm32", features = ["unstable-traits", "nightly", "stm32l072cz", "time-driver-any", "exti", "memory-x"]  }
 embassy-boot-stm32 = { version = "0.1.0", path = "../../../../embassy-boot/stm32", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/stm32l0/src/bin/a.rs

@@ -11,7 +11,7 @@ use embassy_stm32::exti::ExtiInput;
 use embassy_stm32::flash::{Flash, WRITE_SIZE};
 use embassy_stm32::gpio::{Input, Level, Output, Pull, Speed};
 use embassy_sync::mutex::Mutex;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[cfg(feature = "skip-include")]
@@ -46,6 +46,6 @@ async fn main(_spawner: Spawner) {
 
     updater.mark_updated().await.unwrap();
     led.set_low();
-    Timer::after(Duration::from_secs(1)).await;
+    Timer::after_secs(1).await;
     cortex_m::peripheral::SCB::sys_reset();
 }

examples/boot/application/stm32l0/src/bin/b.rs

@@ -6,7 +6,7 @@
 use defmt_rtt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
@@ -16,9 +16,9 @@ async fn main(_spawner: Spawner) {
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
     }
 }

examples/boot/application/stm32l1/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
 embassy-stm32 = { version = "0.1.0", path = "../../../../embassy-stm32", features = ["unstable-traits", "nightly", "stm32l151cb-a", "time-driver-any", "exti"]  }
 embassy-boot-stm32 = { version = "0.1.0", path = "../../../../embassy-boot/stm32", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/stm32l1/src/bin/a.rs

@@ -11,7 +11,7 @@ use embassy_stm32::exti::ExtiInput;
 use embassy_stm32::flash::{Flash, WRITE_SIZE};
 use embassy_stm32::gpio::{Input, Level, Output, Pull, Speed};
 use embassy_sync::mutex::Mutex;
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[cfg(feature = "skip-include")]
@@ -46,6 +46,6 @@ async fn main(_spawner: Spawner) {
 
     updater.mark_updated().await.unwrap();
     led.set_low();
-    Timer::after(Duration::from_secs(1)).await;
+    Timer::after_secs(1).await;
     cortex_m::peripheral::SCB::sys_reset();
 }

examples/boot/application/stm32l1/src/bin/b.rs

@@ -6,7 +6,7 @@
 use defmt_rtt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
@@ -16,9 +16,9 @@ async fn main(_spawner: Spawner) {
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
     }
 }

examples/boot/application/stm32l4/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
 embassy-stm32 = { version = "0.1.0", path = "../../../../embassy-stm32", features = ["unstable-traits", "nightly", "stm32l475vg", "time-driver-any", "exti"]  }
 embassy-boot-stm32 = { version = "0.1.0", path = "../../../../embassy-boot/stm32", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/stm32l4/src/bin/b.rs

@@ -6,7 +6,7 @@
 use defmt_rtt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
@@ -16,9 +16,9 @@ async fn main(_spawner: Spawner) {
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
     }
 }

examples/boot/application/stm32wl/Cargo.toml

@@ -7,7 +7,7 @@ license = "MIT OR Apache-2.0"
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "nightly", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
+embassy-time = { version = "0.1.5", path = "../../../../embassy-time", features = ["nightly", "tick-hz-32_768"] }
 embassy-stm32 = { version = "0.1.0", path = "../../../../embassy-stm32", features = ["unstable-traits", "nightly", "stm32wl55jc-cm4", "time-driver-any", "exti"]  }
 embassy-boot-stm32 = { version = "0.1.0", path = "../../../../embassy-boot/stm32", features = ["nightly"] }
 embassy-embedded-hal = { version = "0.1.0", path = "../../../../embassy-embedded-hal" }

examples/boot/application/stm32wl/src/bin/b.rs

@@ -6,7 +6,7 @@
 use defmt_rtt::*;
 use embassy_executor::Spawner;
 use embassy_stm32::gpio::{Level, Output, Speed};
-use embassy_time::{Duration, Timer};
+use embassy_time::Timer;
 use panic_reset as _;
 
 #[embassy_executor::main]
@@ -16,9 +16,9 @@ async fn main(_spawner: Spawner) {
 
     loop {
         led.set_high();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
 
         led.set_low();
-        Timer::after(Duration::from_millis(500)).await;
+        Timer::after_millis(500).await;
     }
 }

examples/nrf-rtos-trace/Cargo.toml

@@ -18,7 +18,7 @@ log = [
 [dependencies]
 embassy-sync = { version = "0.3.0", path = "../../embassy-sync" }
 embassy-executor = { version = "0.3.0", path = "../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "rtos-trace", "rtos-trace-interrupt", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../embassy-time" }
+embassy-time = { version = "0.1.5", path = "../../embassy-time" }
 embassy-nrf = { version = "0.1.0", path = "../../embassy-nrf", features = ["nrf52840", "time-driver-rtc1", "gpiote", "unstable-pac"] }
 
 cortex-m = { version = "0.7.6", features = ["inline-asm", "critical-section-single-core"] }

examples/nrf-rtos-trace/src/bin/rtos_trace.rs

@@ -6,7 +6,7 @@ use core::future::poll_fn;
 use core::task::Poll;
 
 use embassy_executor::Spawner;
-use embassy_time::{Duration, Instant, Timer};
+use embassy_time::{Instant, Timer};
 #[cfg(feature = "log")]
 use log::*;
 use panic_probe as _;
@@ -34,7 +34,7 @@ async fn run1() {
         info!("DING DONG");
         #[cfg(not(feature = "log"))]
         rtos_trace::trace::marker(13);
-        Timer::after(Duration::from_ticks(16000)).await;
+        Timer::after_ticks(16000).await;
     }
 }
 

examples/nrf52840-rtic/Cargo.toml

@@ -9,7 +9,7 @@ rtic = { version = "2", features = ["thumbv7-backend"] }
 
 embassy-futures = { version = "0.1.0", path = "../../embassy-futures" }
 embassy-sync = { version = "0.3.0", path = "../../embassy-sync", features = ["defmt"] }
-embassy-time = { version = "0.1.4", path = "../../embassy-time", features = ["nightly", "unstable-traits", "defmt", "defmt-timestamp-uptime", "generic-queue"] }
+embassy-time = { version = "0.1.5", path = "../../embassy-time", features = ["nightly", "unstable-traits", "defmt", "defmt-timestamp-uptime", "generic-queue"] }
 embassy-nrf = { version = "0.1.0", path = "../../embassy-nrf", features = ["nightly", "unstable-traits", "defmt", "nrf52840", "time-driver-rtc1", "gpiote", "unstable-pac", "time"] }
 
 defmt = "0.3"

examples/nrf52840-rtic/src/bin/blinky.rs

@@ -9,7 +9,7 @@ mod app {
     use defmt::info;
     use embassy_nrf::gpio::{Level, Output, OutputDrive};
     use embassy_nrf::peripherals;
-    use embassy_time::{Duration, Timer};
+    use embassy_time::Timer;
 
     #[shared]
     struct Shared {}
@@ -34,10 +34,10 @@ mod app {
         loop {
             info!("off!");
             led.set_high();
-            Timer::after(Duration::from_millis(300)).await;
+            Timer::after_millis(300).await;
             info!("on!");
             led.set_low();
-            Timer::after(Duration::from_millis(300)).await;
+            Timer::after_millis(300).await;
         }
     }
 }

examples/nrf52840/Cargo.toml

@@ -31,7 +31,7 @@ nightly = [
 embassy-futures = { version = "0.1.0", path = "../../embassy-futures" }
 embassy-sync = { version = "0.3.0", path = "../../embassy-sync", features = ["defmt"] }
 embassy-executor = { version = "0.3.0", path = "../../embassy-executor", features = ["arch-cortex-m", "executor-thread", "executor-interrupt", "defmt", "integrated-timers"] }
-embassy-time = { version = "0.1.4", path = "../../embassy-time", features = ["defmt", "defmt-timestamp-uptime"] }
+embassy-time = { version = "0.1.5", path = "../../embassy-time", features = ["defmt", "defmt-timestamp-uptime"] }
 embassy-nrf = { version = "0.1.0", path = "../../embassy-nrf", features = ["defmt", "nrf52840", "time-driver-rtc1", "gpiote", "unstable-pac", "time"] }
 embassy-net = { version = "0.1.0", path = "../../embassy-net", features = ["defmt", "tcp", "dhcpv4", "medium-ethernet"], optional = true }
 embassy-usb = { version = "0.1.0", path = "../../embassy-usb", features = ["defmt", "msos-descriptor",], optional = true }