With a large enough HSE input frequency, the vco clock calculation will
overflow a u32. Therefore, in this specific case we have to use the
inner value and cast to u64 to ensure the mul isn't clipped before
applying the divider.
* Add clippy allow to not report if same then branch
* Support enabling RTC clock on STM32WL
* Add clippy allow to not report if same then branch
* Support enabling RTC clock on STM32WL
* Add rtc example for stm32wl
* Address code review feedback
This flag for example permits the following clock tree
configuration on stm32f103r8
let mut config = Config::default();
config.rcc.hse = Some(Hertz(16_000_000));
config.rcc.sys_ck = Some(Hertz(72_000_000));
config.rcc.pclk1 = Some(Hertz(36_000_000));
config.rcc.pclk2 = Some(Hertz(72_000_000));
config.rcc.pllxtpre = true;
Init fails if pllxtpre is false.
1360: stm32/rcc: add i2s pll on some f4 micros r=Dirbaio a=xoviat
Adds the i2s pll on some f4 micros.
1361: Executor: Replace unnecessary atomics in runqueue r=Dirbaio a=GrantM11235
Only the head pointer needs to be atomic. The `RunQueueItem` pointers are only loaded and stored, and never concurrently
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
Co-authored-by: Grant Miller <GrantM11235@gmail.com>
* `MSIRGSEL = 1` was required for MSI accept the updated MSI range
* Reorder enable and clock switching to properly handle the jump from
the default 4MHz MSI to a higher MSI freuquency
- Remove unused `MilliSeconds`, `MicroSeconds`, and `NanoSeconds` types
- Remove `Bps`, `KiloHertz`, and `MegaHertz` types that were only used
for converting to `Hertz`
- Replace all instances of `impl Into<Hertz>` with `Hertz`
- Add `hz`, `khz`, and `mhz` methods to `Hertz`, as well as
free function shortcuts
- Remove `U32Ext` extension trait
- Move Interrupt and InterruptExecutor from `embassy` to `embassy-cortex-m`.
- Move Unborrow from `embassy` to `embassy-hal-common` (nothing in `embassy` requires it anymore)
- Move PeripheralMutex from `embassy-hal-common` to `embassy-cortex-m`.
STM32G0 SYSCLK can be sourced from PLLRCLK. Given that the HSI runs at
16 MHz and the HSE range is 4-48 MHz, the PLL is the only way to reach
64 MHz. This commit adds `ClockSrc::PLL`.
The PLL sources from either HSI16 or HSE, divides it by `m`, and locks
its VCO to multiple `n`. It then divides the VCO by `r`, `p`, and `q`
to produce up to three associated clock signals:
* PLLRCLK is one of the inputs on the SYSCLK mux. This is the main
reason the user will configure the PLL, so `r` is mandatory and
the output is enabled unconditionally.
* PLLPCLK is available as a clock source for the ADC and I2S
peripherals, so `p` is optional and the output is conditional.
* PLLQCLK exists only on STM32G0B0xx, and exists only to feed the
MCO and MCO2 peripherals, so `q` is optional and the output is
conditional.
When the user specifies `ClockSrc::PLL(PllConfig)`, `rcc::init()`
calls `PllConfig::init()` which initializes the PLL per [RM0454]. It
disables the PLL, waits for it to stop, enables the source
oscillator, configures the PLL, waits for it to lock, and then
enables the appropriate outputs. `rcc::init()` then switches the
clock source to PLLRCLK.
`rcc::init()` is now also resonsible for calculating and setting flash
wait states. SYSCLCK < 24 MHz is fine in the reset state, but 24-48 MHz
requires waiting 1 cycle and 48-64 MHz requires waiting 2 cycles. (This
was likely a blocker for anyone using HSE >= 24 MHz, with or without
the PLL.) Flash accesses are now automatically slowed down as needed
before changing the clock source, and sped up as permitted after
changing the clock source. The number of flash wait states also
determines if flash prefetching will be profitable, so that is now
handled automatically too.
[RM0454]: https://www.st.com/resource/en/reference_manual/rm0454-stm32g0x0-advanced-armbased-32bit-mcus-stmicroelectronics.pdf
