this removed the RelocatedProgram construction step from pio uses.
there's not all that much to be said for the extra step because the
origin can be set on the input program itself, and the remaining
information exposed by RelocatedProgram can be exposed from
LoadedProgram instead (even though it's already available on the pio_asm
programs, albeit perhaps less convenient). we do lose access to the
relocated instruction iterator, but we also cannot think of anything
this iterator would actually be useful for outside of program loading.
- don't require an irq binding for blocking-only adc
- abstract adc pins into an AnyPin like interface, erasing the actual
peripheral type at runtime.
- add pull-up/pull-down functions for adc pins
- add a test (mostly a copy of the example, to be honest)
- configure adc pads according to datasheet
- report conversion errors (although they seem exceedingly rare?)
- drop embedded-hal interfaces. embedded-hal channels can do neither
AnyPin nor pullup/pulldown without encoding both into the type
1457: TL Mbox read and write for stm32wb r=xoviat a=OueslatiGhaith
Hello,
This pull request is related to #1397 and #1401, inspired by #24, built upon the work done in #1405 and #1424, and was tested on an stm32wb55rg.
This pull request aims to add read and write functionality to the TL mailbox for stm32wb microcontrollers
Co-authored-by: goueslati <ghaith.oueslati@habemus.com>
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
1458: rp: remove take!, add bind_interrupts! r=Dirbaio a=pennae
both of the uart interrupts now check a flag that only the dma rx path ever sets (and now unsets again on drop) to return early if it's not as they expect. this is ... not our preferred solution, but if bind_interrupts *must* allow mutiple handlers to be specified then this is the only way we can think of that doesn't break uarts.
Co-authored-by: pennae <github@quasiparticle.net>
1424: add TL maibox for stm32wb r=xoviat a=OueslatiGhaith
Hello,
This pull request is related to #1397 and #1401, inspired by #24, build upon the work done in #1405, and was tested on an stm32wb55rg.
This pull request aims to add the transport layer mailbox for stm32wb microcontrollers. For now it's only capable of initializing it and getting the firmware information
Co-authored-by: goueslati <ghaith.oueslati@habemus.com>
Co-authored-by: Ghaith Oueslati <73850124+OueslatiGhaith@users.noreply.github.com>
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
1423: rp: fix gpio InputFuture and inefficiencies r=pennae a=pennae
InputFuture could not wait for edges without breaking due to a broken From impl, but even if the impl had been correct it would not have worked correctly because raw edge interrupts are sticky and must be cleared from software. also replace critical sections with atomic accesses, and do nvic setup only once.
Co-authored-by: pennae <github@quasiparticle.net>
doing this setup work repeatedly, on every wait, is unnecessary. with
nothing ever disabling the interrupt it is sufficient to enable it once
during device init and never touch it again.
1422: rp: remove leftovers from #1414 r=Dirbaio a=pennae
forgot to remove these when they were no longer necessary or useful. oops.
Co-authored-by: pennae <github@quasiparticle.net>
1376: rtc: cleanup and consolidate r=Dirbaio a=xoviat
This removes an extra file that I left in, adds an example, and consolidates the files into one 'v2' file.
Co-authored-by: xoviat <xoviat@users.noreply.github.com>
