WindowWatchdog configures a timer channel to capture both edges of an
input and compare the time between edges to a duration range. In other
words, it expects a ~50% duty cycle square wave on its input.
One possible use for this is to monitor whether another device is
functional.
If VALID_THRESHOLD (currently 2) edge intervals are within range, ok()
returns true, otherwise, if an edge is outside of the valid range ok()
returns false.
state_change() runs the calling task whenever the ok() state changes.
1228: stm32/sdmmc: Implement proper clock configuration r=chemicstry a=chemicstry
This implements proper clock configuration for sdmmc based on chip family, because `RccPeripheral::frequency()` is almost always incorrect. This can't be fixed in PAC, because sdmmc uses two clock domains, one for memory bus and one for sd card. `RccPeripheral::frequency()` usually returns the memory bus clock, but SDIO clock calculations need sd card domain clock. Moreover, chips have multiple clock source selection bits, which makes this even more complicated. I'm not sure if it's worth implementing all this logic in `RccPeripheral::frequency()` instead of cfg's in sdmmc.
Some chips (Lx, U5, H7) require RCC updates to expose required clocks. I didn't want to mash everything in a single PR so left a TODO comment. I also left a `T::frequency()` fallback, which seemed to work in H7 case even though the clock is most certainly incorrect.
In addition, added support for clock divider bypass for sdmmc_v1, which allows reaching a maximum clock of 48 MHz. The peripheral theoretically supports up to 50 MHz, but for that ST recommends setting pll48 frequency to 50 MHz 🤔
Co-authored-by: chemicstry <chemicstry@gmail.com>
1227: stm32/dma: fix spurious transfer complete interrupts r=Dirbaio a=pattop
DMA interrupts must be acknowledged by writing to the DMA_{L,H}IFCR
register.
Writing to the CR register is unnecessary as the channel (EN bit) is
disabled by hardware on completion of the transfer.
Co-authored-by: Patrick Oppenlander <patrick.oppenlander@gmail.com>
DMA interrupts must be acknowledged by writing to the DMA_{L,H}IFCR
register.
Writing to the CR register is unnecessary as the channel (EN bit) is
disabled by hardware on completion of the transfer.
1200: feat(stm32): Add 16 data bit fmc ctor r=Dirbaio a=rmja
This has been validated with the Is42s16400j sdram on stm32f429.
Co-authored-by: Rasmus Melchior Jacobsen <rmja@laesoe.org>
1199: STM32 SPI: Set clk-pin pull-up/-down to match spi clock polarity r=Dirbaio a=jr-oss
Fixes#1094
There are some proposed solutions in #1094
> Keep the DMA transaction open across calls to read/write
This may be problematic if the user changes bus settings between calls, and also the reference manual says the chip should not be placed into low power mode while SPI is enabled
As already described, this is problematic and against reference manual recommendation
> Set the CLK (and maybe MOSI) pins as pull-down on setup (or pull-up, depending on config - and this would need to be updated if the user modified the config)
This is less good than driving the pin to the correct value, but may be better than nothing
That is also my preferred solution. See below citation from reference manual.
> Document this and require users fix it themselves (add a pull-up/down resistor - or configure the pins as pull-up/pull-down before passing them into SPI setup)
Setting internal pull-up/-down won't work, because `sck.set_as_af()` will change the gpio pull mode to none: https://github.com/embassy-rs/embassy/blob/master/embassy-stm32/src/gpio.rs#L552-L555
> Dig around in the reference manual and determine if there is a better way to start/stop a DMA transaction while keeping active control of the clock the whole time
I haven't found a better way
------
From ST reference manual RM0394 (L4)
(Same note in RM0399 (H7) / RM0038 (L1) / RM0316 /F3)):
40.4.6
Communication formats
...
The idle state of SCK must correspond to the polarity selected in the SPIx_CR1 register (by
pulling up SCK if CPOL=1 or pulling down SCK if CPOL=0).
Co-authored-by: Ralf <jr-oss@gmx.net>
RM0394:
40.4.6
Communication formats
...
The idle state of SCK must correspond to the polarity selected in the SPIx_CR1 register (by
pulling up SCK if CPOL=1 or pulling down SCK if CPOL=0).
- Rename feature to `embedded-sdmmc`.
- Move embedded-sdmmc fork repo to the embassy-rs org.
- Remove unused features in the fork
- Fix impl in embassy-stm32
- Add to CI so it doesn't break again.
1159: stm32 usb otg bug fixes r=Dirbaio a=chemicstry
This fixes a couple of usb otg bugs that surfaced with `usb_ethernet` example from nrf:
- Properly implemented `Endpoint::wait_enabled()`
- Return `EndpointError::Disabled` when neccessary in `Endpoint::write()`
Co-authored-by: chemicstry <chemicstry@gmail.com>
